manualshive.com logo in svg

Royal Enfield Bullet Classic EFI, Service Manual, Page: 267 / 301

Share
Download
Royal Enfield Bullet Classic EFI Service Manual Download Page 267

ROYAL ENFIELD    VEHICLE SERVICE MANUAL - EURO IV

266

STEP 3 :

The positive probe of the multimeter shall be kept on all the 3 phase terminals one by one and the
 condition of the 3 diodes to be checked as mentioned in Step 2.

STEP 4 :

To check the condition of other 3 negative diodes, positive probe (Red colour) of the multimeter shall be kept on the

negative terminal of DC output (black wire with eyelet/single pole connector) and negative probe (Black colour) of

the multimeter shall be kept on anyone of the 3 phase terminals (yellow wire).
If the diode is good, then the multimeter will show a voltage drop of 0.4~0.7V.
If diode has failed, multimeter will show either open or short with beep sound, then Replace the RR unit.

STEP 5 :

All the three diodes to be checked by keeping the multimeter negative probe on all the 3 phase terminals one by one.

If the RR Unit is not working, replace with good working RR Unit.

DC Output Terminals

3 Phase AC Terminals

KS MOTORCYCLES - http://ksmotorcycles.com

Summary of Contents for Bullet Classic EFI














































































































































































































































































































Reviews:

No comments