Home
/
Royal Enfield
/
Bullet Classic EFI
/
Service Manual

Royal Enfield Bullet Classic EFI, Service Manual, Page: 265 / 301

Share

Page: 265 / 301

Royal Enfield Bullet Classic EFI Service Manual Download Page 265

ROYAL ENFIELD VEHICLE SERVICE MANUAL - EURO IV

264

INSPECTION

1. COIL RESISTANCE CHECK

a. Set the Multimeter in Resistance check mode.
b. Keep the positive (Red) probe of the Multimeter on coil positive and Negative probe(Black) of the Multimeter on

coil negative.(Refer the below table for polarity identification).

c. Resistance Spec – 3.24 to 3.96



d. If resistance deviates from the specification or if coil is open/short , Relay starter to be replaced.

1. TO CHECK -CONTACT CLOSURE AFTER ENERGISING:

1. Give a supply voltage of 12V across the relay coil ( 2 pole female terminal). Battery positive on coil positive and

Battery negative on coil negative.

2. After energizing the coil, check the continuity between Bve terminal and Sve terminal (Ring

terminal) using Multimeter. If the Multimeter indicates 0Ù with a beep sound, the contacts have got closed. If the

Multimeter indicates as open (OL) ,contacts have not closed and hence the Relay starter has to be replaced.

Energised the relay

using battery

Bve terminal

Starter motor +ve eyelet terminal

Sl.No. Euro IV

Coil Polarity & Wire Color

1.

Classic 500

Coil +ve = Blue

Model

Coil -ve = White

2.

GT

Coil +ve = Brown / Green

Model

Coil -ve = Brown / Blue

KS MOTORCYCLES - http://ksmotorcycles.com

«
...
263
264
265
266
267
...
»

Summary of Contents for Bullet Classic EFI














































































































































































































































































































Reviews:

No comments