Royal Enfield Bullet Classic EFI Service Manual Download Page 260

Page: 260 / 301

ROYAL ENFIELD VEHICLE SERVICE MANUAL - EURO IV

259

No.

Fastener, Size, Tool Usage, Precautions, Photos

Aggregate to Dismantle /

Instructions

12.2 Console Bulb

Bullet Classic EFI /

Bullet EFI
Dismantling

12.2 Cluster Bulb

Continental GT
Dismantling

Never touch the bulb with

your fingers, Finger prints

will etch the glass and

decrease bulb life. Always

hold the bulb with paper or

clean dry cloth during

handling.



Disconnect the couplers.



Gently pull out the out

the bulb.



Disconnect the couplers



Gently pull out the bulb

(Speedo meter/Neutral/

High beam& Low beam/

Turn Signal Bulbs) from

its holder.

CONSOLE BULBS REPLACEMENT

KS MOTORCYCLES - http://ksmotorcycles.com

Summary of Contents for Bullet Classic EFI














































































































































































































































































































Search results

Summary of Contents for Bullet Classic EFI

Reviews:

Royal Enfield Bullet Classic EFI, Service Manual, Page: 260 / 301

Search results

Summary of Contents for Bullet Classic EFI

Reviews: