manualshive.com logo in svg

Royal Enfield Bullet Classic EFI, Service Manual, Page: 229 / 301

Share
Download
Royal Enfield Bullet Classic EFI Service Manual Download Page 229

ROYAL ENFIELD    VEHICLE SERVICE MANUAL - EURO IV

228

ROYAL ENFIELD NACS II DIAGNOSIS

Adjust CO value
by clicking
           and click
to                        save
adjusted value.

12-20.

This software is for reading NACS II handheld
recorded data. Please take out SD card from NACS II
handheld tool and insert SD card to PC.

13. RECORD ANALYZING SOFTWARE

Open the
software of
‘NACSII_Record_Royal’.
Select ‘Analyze
Record Data’.

13.1.

Select Record Date
and File name, then
click

13-2.

Select the items
which used often.
Selected items will be
listed in the block of
‘Live Data Item’.
Click                to view
wave chart of
selected items.

13-3.

13-4.

Wave chart starts running until press ‘Stop’ button.
Drag Yellow line forward and back to view recorded
live data values.

KS MOTORCYCLES - http://ksmotorcycles.com

Summary of Contents for Bullet Classic EFI














































































































































































































































































































Reviews:

No comments