Home
/
Royal Enfield
/
Bullet Classic EFI
/
Service Manual

Royal Enfield Bullet Classic EFI, Service Manual, Page: 221 / 301

Share

Page: 221 / 301

Royal Enfield Bullet Classic EFI Service Manual Download Page 221

ROYAL ENFIELD VEHICLE SERVICE MANUAL - EURO IV

220

ROYAL ENFIELD NACS II DIAGNOSIS

Press to view
‘History ‘ DTC.
Press to view next
page and press
to view last page.

After viewing all the

current DTC.
Press to exit. The
screen will return to
the previous page.

11-A9.

F2

C

Freeze Data. ‘Freeze Data’ is the data recorded when

First DTC occured, and one time only record One DTC

freeze data. It’s for saving the engine dynamic data for

further analysis.

11-A10.

When displays on the screen, press to view
freeze data. Press and to view next page and
last page. After viewing all content, press
to exit. The screen will return to the previous page.

Erace DTC. It’s the

function to erace

Diagnostic Trouble

Code in both

‘Current’ and

‘History’.

11-A11.

Press to erace.

To confirm erasing
DTC. Press ‘Yes’.

When showing on the screen, it means the DTC

has been erased. Press to go back to the main menu.

When the screen

returns to the main

menu, move the

cursor to ‘Live Data’
and Press to
view the content.

11-A12.

OK

C

F4

F1

OK

KS MOTORCYCLES - http://ksmotorcycles.com

«
...
219
220
221
222
223
...
»

Summary of Contents for Bullet Classic EFI














































































































































































































































































































Reviews:

No comments