manualshive.com logo in svg

Royal Enfield Bullet Classic EFI, Service Manual, Page: 213 / 301

Share
Download
Royal Enfield Bullet Classic EFI Service Manual Download Page 213

ROYAL ENFIELD    VEHICLE SERVICE MANUAL - EURO IV

212

INSTRUCTIONS (DO’S & DON’T’S)

1) DO NOT remove any of the sensor connections / couplers / Battery connections when the Ignition switch is ON OR

the engine is running.

2) DO ensure the battery is in good condition & Fully Charged Battery.

3) DO start the engine only when it is in centre stand or when rider sitting on the vehicle with both the stands retracted.

(Engine will NOT Start OR switch OFF if side stand is extended).

4) DO NOT rev the engine fully – immediately after starting OR just before shutting off the engine.

5) DO NOT remove the fuel hose (high pressure) from the fuel pump to fuel injector, when engine is running OR with

the ignition switch ON. Fuel flows at a very high pressure during these times.

6) DO NOT use a booster or high voltage-charging unit instead of a battery. Use only a good, correctly charged battery

to start OR check the motorcycle.

7) DO NOT use high pressure water jet to clean the ECU / Throttle Body / any of the sensors. Keep them well protected

while washing the vehicle.

KS MOTORCYCLES - http://ksmotorcycles.com

Summary of Contents for Bullet Classic EFI














































































































































































































































































































Reviews:

No comments