manualshive.com logo in svg

Royal Enfield Bullet Classic EFI, Service Manual, Page: 2 / 301

Share
Download
Royal Enfield Bullet Classic EFI Service Manual Download Page 2

ROYAL ENFIELD    VEHICLE SERVICE MANUAL - EURO IV

1

PREFACE

“

FIRST TIME RIGHT” is a very important element for enhancing Customer Satisfaction.

Royal Enfield is committed to upgrade the skills and knowledge of technicians so that they follow scientific repair

techniques to ensure “FIRST TIME RIGHT” practices and carry out repairs accurately so that customers will enjoy

trouble free performance at all times.

This Maintenance and service manual is specifically for the following EURO IV Regulation models being currently sold

only in UK & European countries.

BULLET EFI

BULLET CLASSIC EFI

CONTINENTAL GT

This Manual is intended for use primarily by a person who is well versed with basic repair technique of a motorcycle

& usage of general purpose tools and special service tools & diagnostic tools, while basic & routine service maintenance

may be in the event of not having possibility in carrying out using basic tools, required tools it is recommended that

the motorcycle may please be get inspected and serviced through an Authorized Royal Enfield Service Station.

This manual will help in guide in the basic servicing, periodical maintenance, systematic disassembly, Parts inspection

and assembling procedures of various mechanisms / systems of the motorcycle which has to be carried out in Royal

Enfield Authorised Dealership or Service Station.

While this manual is updated with latest Information and Specifications, at the time of going to print, due to continuous

improvements being done to improve performance, some of the data, illustrations etc., in this manual may differ

from the actual parts fitted in the engine.

Subsequent & continuous improvement that may be done on the motorcycles to enhance customer satisfaction, will

be uploaded also in the RMI portals & also available with Royal Enfield Authorised dealer & Service Station.

Please do feel free to write to us at

[email protected],

if you have any queries, clarification, suggestions or

feedback.

With warm regards

SERVICE HEAD QUARTERS
Royal Enfield,  A Unit of Eicher Motors Limited,
Thiruvottiyur High Road, Thiruvottiyur, Chennai - 600 019.
E-mail: [email protected]
Website: www.royalenfield.com

Part No: 888569 / Feb. ’17

ROYAL ENFIELD    VEHICLE SERVICE MANUAL - EURO IV

01

KS MOTORCYCLES - http://ksmotorcycles.com

Summary of Contents for Bullet Classic EFI














































































































































































































































































































Reviews:

No comments