manualshive.com logo in svg

Royal Enfield Bullet Classic EFI, Service Manual, Page: 198 / 301

Share
Download
Royal Enfield Bullet Classic EFI Service Manual Download Page 198

ROYAL ENFIELD    VEHICLE SERVICE MANUAL - EURO IV

197

10.14

Crank position

sensor

Locate  Crank  position

sensor inside the cover

RH  of  the  engine

assembly.

Install 3 Hex Socket Head

Cap Screw M5 X 30, on

stator coil to cover RH

inside.

Install 2 Hex Flange Bolt

M5 X 0.8 X 16, on Pulsar

coil to cover RH inside

Locate gasket.

Install and tighten 1 Hex

Flange Bolt M6 X 1 X 45

on cover RH rear

Install and tighten 7 Hex

Flange Bolt M6 X 1 X 70

on cover RH, top, centre

and bottom.

Install and tighten 2 Hex

Flange Bolt M6 X 1 X 85

on cover RH front.

Connect Magneto wiring

coupler in the electrical

harness.

 Fill engine oil.

CAUTION:

Ensure stator coupler

is disconnected before

removing cover RH.

Gently tap on the tabs

provided in the front

and rear of Cover RH to

release the cover from

the crankcase.

S.

No.

Fastener,  Size, Tool Usage, Precautions, Photos

Aggregate to Assemble /

Instructions

KS MOTORCYCLES - http://ksmotorcycles.com

Summary of Contents for Bullet Classic EFI














































































































































































































































































































Reviews:

No comments