Royal Enfield Bullet Classic EFI Service Manual Download Page 191

Page: 191 / 301

ROYAL ENFIELD VEHICLE SERVICE MANUAL - EURO IV

190

No.

Fastener, Size, Tool Usage, Precautions, Photos

Aggregate to Dismantle /

Instructions

10.7

Ambient Air (TA)

Sensor

A. Bullet & Classic

EFI Models



The TA sensor is

assembled behind the

Filter box assembly and

can be removed only

after removing the air

filter housing from the

frame

(Refer section 5.2

Air filter.)



Ensure Ignition switch

and stop switch are in

OFF position.



Disconnect the wiring

coupler from the TA

sensor.



Loosen and remove 2

Hex Soc Hd cap screws,

holding TA sensor to

Filter Box Assembly.



Remove TA sensor with

gasket.

Philips head screws
Philips Screw driver

Hex Soc Hd Cap Screws:

M5 X 20
Allen Key: 4mm

B. Continental GT

Model



The TA sensor is assembled

on the pipe outlet bet-

ween air filter housing

and Throttle body.



Ensure Ignition switch

and stop switch are in

OFF position.



Remove seat assembly

(Refer section 5.4)



Disconnect the wiring

coupler from the TA

sensor.



Using a long reach Philips

head screw driver,

loosen and remove the 2

screws, holding TA

sensor to pipe outlet.



Remove TA sensor along

with gasket, from pipe

outlet.

KS MOTORCYCLES - http://ksmotorcycles.com

Summary of Contents for Bullet Classic EFI














































































































































































































































































































Search results

Summary of Contents for Bullet Classic EFI

Reviews:

Royal Enfield Bullet Classic EFI, Service Manual, Page: 191 / 301

Search results

Summary of Contents for Bullet Classic EFI

Reviews: