manualshive.com logo in svg

Royal Enfield Bullet Classic EFI, Service Manual, Page: 186 / 301

Share
Download
Royal Enfield Bullet Classic EFI Service Manual Download Page 186

ROYAL ENFIELD    VEHICLE SERVICE MANUAL - EURO IV

185

10.2

Crank position

sensor

The  Crank  position

sensor is located inside

the  cover  RH  of  the

engine assembly.

Drain engine oil from the

engine.

Ensure Ignition switch

and stop switch are  in

OFF position.

Disconnect  Magneto

wiring coupler from the

electrical harness.

Loosen  and  remove  2

Hex Flange Bolt M6 X 1 X

85 from cover RH front.

Loosen  and  remove  7

Hex Flange Bolt M6 X 1 X

70 from cover RH, top,

centre and bottom.

Loosen  and  remove  1

Hex Flange Bolt M6 X 1 X

45 from cover RH rear.

It may be necessary to

gently tap and remove

cover RH as the magnetic

forces in the rotor can be

acting on the stator and

making  it  difficult  to

remove.

Remove gasket.

Remove  2  Hex  Flange

Bolt  M5  X  0.8  X  16,

holding  Pulsar  coil  to

cover RH inside.

Remove  3  Hex  Socket

Head Cap Screw M5 X 30,

holding  stator  coil  to

cover RH inside.

Fastener,  Size, Tool Usage, Precautions, Photos

Aggregate to Dismantle /

Instructions

S.

No.

CAUTION:

Ensure stator coupler is

disconnected  before

removing cover RH.

Gently tap on the tabs

provided  in  the  front

and rear of Cover RH to

release the cover from

the crankcase.

KS MOTORCYCLES - http://ksmotorcycles.com

Summary of Contents for Bullet Classic EFI














































































































































































































































































































Reviews:

No comments