Roving Networks RN-171XVS-I/RM User Manual Download

Page: 12 / 14

www.rovingnetworks.com

Version 1.01 9/28/2012

RN-XV-RD2-EVAL-UM

RESOURCES & RELATED DOCUMENTS

For more information, refer to the following sources, which are available on the Support page on the Roving Networks
website at

http://www.rovingnetworks.com/support.php

•

RN-XV Data Sheet

•

RN-171 Data Sheet

•

WiFly Advanced User Manual

•

WiFly Training Presentation

•

Drivers, tools, and utilities

ORDERING INFORMATION

Table 4 provides ordering information. For the evaluation described in this document, Roving Networks recommends
purchasing the RN-XV-W, which has a ¼ inch wire antenna.

! "

Part Number

Description

RN-XV-RD2

Evaluation board.

RN-171XVW-I/RM

Standard configuration, industrial temperature, Wi-Fi, 802.15.4 replacement solution with ¼ inch

wire antenna. For other configurations, contact Roving Networks directly.

RN-171XVS-I/RM

Custom configuration, industrial temperature (-40

C to +85

C) Wi-Fi, 802.15.4 replacement

solution with SMA connector.

RN-171XVU-I/RM

Custom configuration, industrial temperature (-40

C to +85

C) Wi-Fi, 802.15.4 replacement

solution with U.FL. connector.

RN-USB-SERIAL

USB cable.

Go to http://www.rovingnetworks.com for current pricing and a list of distributors carrying Roving Networks products.

Summary of Contents for RN-171XVS-I/RM














Search results

Summary of Contents for RN-171XVS-I/RM

Reviews:

Related manuals for RN-171XVS-I/RM

Brands by name

Popular brands

Roving Networks RN-171XVS-I/RM, User Manual

Search results

Summary of Contents for RN-171XVS-I/RM

Reviews:

Related manuals for RN-171XVS-I/RM

Brands by name

Popular brands