Rotex RKHWMX300C Page 60 Installation And Maintenance Instructions Manual Download

Page: 60 / 72

FA ROTEX HPSU monobloc compact • 09/2017

Errors, malfunctions and messages

8.4

Control and configuration of DIP switches

De-energise the system.

Check the DIP switch setting on the RoCon BM2C printed
circuit board of the ROTEX HPSU monobloc compact, and
adjust if necessary (see fig. 8-5).

The factory setting must not be changed.

Close the controller housing and restore the voltage supply.

8.5

Emergency operation

Emergency heating operation can be maintained if the electronic
controller settings are incorrect by activating the special "Manual
Operation" function on the controller (see controller operating
instructions).

If the 3-way valves are intact, the ROTEX HPSU monobloc com-
pact switches to

heating mode

. The required inflow temperature

can be adjusted with the rotary switch.

Fig. 8-4

Components in the heat pump outdoor unit (simplified sche-
matic)

Plate heat exchanger (condenser)

Fan motor

Fin heat exchanger (evaporator)

Filter

Electronic expansion valve

Shut-off valve (fluid line)

Service valve with maintenance connection (gas pipe)

Accumulator

Refrigerant compressor

4-way switch valve (—> heating,

····

> cooling)

R1T

Feed temperature sensor

R2T

Outlet temperature sensor (refrigerant compressor)

R3T

Fluid line temperature sensor

R4T

Return flow temperature sensor

R5T

Centre fin heat exchanger temperature sensor

S1PH

High-pressure switch

S1NPH

Pressure sensor

Outdoor unit water inlet valve

Outdoor unit water outlet valve

Diaphragm expansion vessel

Filter

Pressure relief valve

Vent valve

Flow sensor FLS

Circulation pump

Flow rate switch

Tab. 8-3 Legend for fig. 8-4

WARNING!

Touching live parts can result in an

electric

shock

and lead to potentially fatal injuries and

burns.

Before beginning work on live parts,

disconnect all of the systems circuits
from the power supply

(switch off external

main switch, disconnect fuse) and secure
against unintentional restart.

Fig. 8-5

DIP switch setting on RoCon BM2C

DIP switch settings are not recognised until a brief inter-
ruption to the power supply.

Summary of Contents for RKHWMX300C









































































Search results

Summary of Contents for RKHWMX300C

Reviews:

Related manuals for RKHWMX300C

Brands by name

Popular brands

Rotex RKHWMX300C, Installation And Maintenance Instructions Manual

Search results

Summary of Contents for RKHWMX300C

Reviews:

Related manuals for RKHWMX300C

Brands by name

Popular brands