Rotex RKHWMX300C Page 57 Installation And Maintenance Instructions Manual Download

Page: 57 / 72

Errors, malfunctions and messages

FA ROTEX HPSU monobloc compact • 09/2017

E9041

Transmission fault Electrical components

Communication between heat pump outdoor unit and heat pump
indoor unit disturbed.

–

Wiring or connections, poor contact.

–

No heat pump outdoor unit connected.

–

Printed circuit board A1P (outdoor unit) defective.

–

Main circuit board in the heat pump outdoor unit defective.

Check, replace.

E9042

Communication between printed circuit board A1P (outdoor unit)
and RoCon BM2C disturbed.

See fault code E200.

E9043

Communication between main circuit board and inverter circuit
board in the heat pump outdoor unit disturbed.

–

Main circuit board in the heat pump outdoor unit defective.

–

Inverter circuit board in the heat pump outdoor unit defective.

–

Wiring, poor contact.

Check, eliminate cause, replace.

E9044

Configuration of printed circuit board A1P (outdoor unit) does not
match the heat pump outdoor unit

Replace printed circuit board A1P.

If necessary, contact a ROTEX service technician.

E9045

heating time (hot
water)

Software

WW heating > 6 hours

Check the heating element.

Check whether the power supply meets the regulations. Check
for frequency fluctuations.

Check the fuses on the printed circuit boards.

Check WW consumption (poss. too high).

Check the building's WW tap.

Confirm that the software and EEPROM on the hydro printed
circuit board match.

E9046

compressor start-
up

Software

System detects an abnormal electricity wave shape 16 times in
5 min

Check whether the power supply meets the regulations. Check
for frequency fluctuations.

Check the compressor.

Check the compressor's connection and wiring.

Check the operation of the expansion valve (fluid return flow).

Check the refrigerant filling capacity, and check for leaks.

After resetting the power supply, check whether the error occurs
when the compressor is not in operation: check the expansion
valve.

E9047

overvoltage

Software

System detects an overcurrent of > 20 A to the compressor for
> 2.5 seconds 16 times in 5 min

Check the compressor.

Check the compressor's connection and wiring.

Check the operation of the expansion valve (fluid return flow).

Check the refrigerant filling capacity, and check for leaks.

Check the power transistor.

Check the outer inverter conductor plate.

Check whether the current flow LED flashes at regular intervals.

Check whether the correct replacement part has been installed.

Check whether the outer main conductor plate is receiving a
power supply.

Check whether the power supply meets the regulations. Check
for frequency fluctuations.

Code

Malfunction /

error message

Component/

Designation

Causes and possible fault elimination

Display Internal

Summary of Contents for RKHWMX300C









































































Search results

Summary of Contents for RKHWMX300C

Reviews:

Related manuals for RKHWMX300C

Brands by name

Popular brands

Rotex RKHWMX300C, Installation And Maintenance Instructions Manual

Search results

Summary of Contents for RKHWMX300C

Reviews:

Related manuals for RKHWMX300C

Brands by name

Popular brands