Rotex RKHWMX300C Page 54 Installation And Maintenance Instructions Manual Download

Page: 54 / 72

FA ROTEX HPSU monobloc compact • 09/2017

Errors, malfunctions and messages

E9011

Fault flow sensor

Flow sensor FLS or flow
switch (outdoor unit)

Flow sensor FLS or flow switch defective.

Replace flow sensor FLS.

Replace flow switch.

E9012

Fault feed flow
sensor

Feed temperature sen-
sor t

(outdoor unit) or

V, BH

Measured value outside of the permissible value range. Sensor or
connecting cable defective.

Check, replace.

E9013

OU main board def

Heat pump outdoor unit
main circuit board

–

Main circuit board in the heat pump outdoor unit defective.

–

Fan motor defective.

Check, replace.

E9014

Coolant over-pres-
sure

High-pressure switch
S1PH in the refrigerant
system (outdoor unit)

Pressure in refrigerant system is too high.

–

High-pressure switch S1PH or fan motor defective.

Check, replace.

–

Poor wiring contact.

–

Flow rate in the heating system too low.

–

Filled refrigerant quantity too high.

Check, replace.

–

Service valves in the heat pump outdoor unit not open.

Open service valves.

E9015

Coolant under-
pressure

Pressure sensor S1NPH
in the heat pump outdoor
unit

Pressure in refrigerant system too low.

–

Refrigerant quantity too low.

Check, eliminate cause, top up refrigerant.

–

Pressure sensor S1NPH in the heat pump outdoor unit defective.

–

Temperature sensor of fin heat exchanger R4T in the heat pump
outdoor unit defective.

–

Solenoid valve in the heat pump outdoor unit not opening.

–

Main circuit board in the heat pump outdoor unit defective.

Check, replace.

E9016

Load protec comp

Electronic overload pro-
tection in the refrigerant
compressor (outdoor
unit)

Refrigerant compressor overload protection has triggered. Pressure
difference in the refrigerant circuit between high and low pressure
side too high (> 26 bar).

–

Refrigerant compressor defective.

–

Inverter circuit board in the heat pump outdoor unit defective.

–

Refrigerant compressor / inverter circuit board wiring, poor con-
tact.

–

Filled refrigerant quantity too high.

Check, replace.

–

Service valves in the heat pump outdoor unit not open.

Open service valves.

E9017

Fan blocked

Fan motor in the heat
pump outdoor unit

–

A fan in the heat pump outdoor unit is blocked.

Check fan for presence of dirt or blockages; if necessary,
clean and free up.

–

Fan motor defective.

–

Fan motor wiring, poor contact.

–

Overvoltage at fan motor.

–

Fuse in the heat pump outdoor unit defective.

–

Inverter circuit board in the heat pump outdoor unit defective.

Check, replace.

E9018

Expansion valve

Electronic expansion
valve (outdoor unit)

–

The electronic expansion valve in the heat pump outdoor unit is
defective.

Check, replace.

E9019

Hot water temper-
ature > 85 °C

Storage tank tempera-
ture sensor t

DHW

The storage tank temperature sensor t

DHW

delivers a temperature

value > 85 °C.

–

Sensor or connecting cable defective.

Check, replace.

E9020

Evaporator over-
temp

Outlet temperature sen-
sor (hot gas sensor) R2T
on the heat pump out-
door unit refrigerant
compressor too high

–

Outlet temperature sensor R2T on the refrigerant compressor
or connecting cable defective.

–

Refrigerant compressor defective.

Check, replace.

Code

Malfunction /

error message

Component/

Designation

Causes and possible fault elimination

Display Internal

Summary of Contents for RKHWMX300C









































































Search results

Summary of Contents for RKHWMX300C

Reviews:

Related manuals for RKHWMX300C

Brands by name

Popular brands

Rotex RKHWMX300C, Installation And Maintenance Instructions Manual

Search results

Summary of Contents for RKHWMX300C

Reviews:

Related manuals for RKHWMX300C

Brands by name

Popular brands