Rosslare Mifare CP-R25 Hardware & Software Manual Download Page 19

Page: 19 / 52

AS-B01 Software Overview and LEDs

CP-R25 Hardware & Software Manual

Page 18

User ID/Card Serial number user cards as well as
Reader configuration cards.

Swipe reader – Used to write and read cards

containing fingerprint templates. This tab also allows

the creation of configuration cards for fingerprint
readers.

•

Message log area – this event log records all activities

provides the user with real time system monitoring. The

information messages may either be operation success or
failure messages, or instruction messages for example

during fingerprints enrollment.

•

Status information area – indicates connection status with

the CP-R25 Desktop Programmer hardware.

4.3

Indication LED’s:

The following table describes LED behavior on the CP-R25

Programmer (see Figure 2: CP-R25 Description).

General

Event

Swipe Card
Reader LED

Fingerprint
Reader

LED

Buzzer

Fingerprint
Directional

Indication

LED

Power
on

One red LED will light for several seconds followed by all the
LEDs flashing and the buzzer beeps 3 times for the duration
of 3 seconds each time

Card Programming

Event

Swipe Card

Reader LED

Fingerprint

Reader

LED

Buzzer

Fingerprint

Directional

Indication
LED

Card not
loaded

Green flashing

All off

Off

All on

Summary of Contents for Mifare CP-R25





















































Search results

Summary of Contents for Mifare CP-R25

Reviews:

Related manuals for Mifare CP-R25

Brands by name

Popular brands

Rosslare Mifare CP-R25, Hardware & Software Manual

Search results

Summary of Contents for Mifare CP-R25

Reviews:

Related manuals for Mifare CP-R25

Brands by name

Popular brands