manualshive.com logo in svg

Ross TES9, Software User Manual

Share
Download
Ross TES9 Software User Manual Download Page 42

5–8 • Captioning Module

TES9 Software User Manual (Iss. 04)

Redistribution Control (Broadcast Flag)

This feature, which is an optional component to the Caption module, allows for the insertion of 
the Redistribution Control Program Descriptor (also referred to as the Broadcast Flag), as defined 
by SMPTE RP207. The inserted VANC packets have Data ID=62 and Secondary Data ID = 01. If 
this optional component is installed then the pull down list is visible at the bottom of the caption 
module screen. The list will show the current setting for the operation of the broadcast flag.

Always Insert Broadcast Flag 

This selection causes the TES9 to insert the Redistribution Control packet every two seconds. 

Always Block Upstream Broadcast Flag

This selection causes the TES9 to ensure that the Redistribution Control packet is never inserted, 
by disabling the “N_PD” command for the Redistribution Control packet and by ignoring the 
GPIO input which controls the insertion of the Redistribution Control packet. Also, if the Encode 
Mode on the main TES9Set menu is set to Add, then all Redistribution Control packets from 
upstream are blocked. 

Broadcast Flag Controlled by GPIO and Commands

This selection allows the insertion of the Redistribution Control packet to be controlled via the 
GPIO port on the rear panel of the TES9 and by the “N_PD” command from the transmit 
computer. When using the GPIO port, an open circuit or a high logic level (i.e. from 2 to 5 volts) 
signals the inactive state, and a low logic level (i.e. from 0 to.8 volts) signals the active state. 
When pin 1 of the GPIO port changes from the inactive to the active state by connecting it to 
ground, then the Redistribution Control packet is inserted within 2 video fields and every 2 
seconds thereafter, until the GPIO input changes back to the inactive state. While the GPIO input 
is in the active state, any Redistribution Control packets received from upstream are blocked (i.e. 
deleted). Whenever the GPIO input is in the inactive state, then the insertion of the Redistribution 
Control packet is controlled via the “N_PD” command from the transmit computer. For details of 
the wiring of the GPIO port, refer to the 

TES9 Hardware Manual

.

Broadcast Flag Controlled by Commands

This selection allows the insertion of the Redistribution Control packet to be controlled by the 
“N_PD” command only. 

Broadcast Flag Disabled (Upstream Passed)

This selection disables the Redistribution Control feature of the Caption module, so that no 
Redistribution Control packet is inserted, and upstream Redistribution Control packets are not 
blocked.

Summary of Contents for TES9





































































Reviews:

No comments

Brands by name

Popular brands

Load more brands