manualshive.com logo in svg

Ross TES9, Software User Manual

Share
Download
Ross TES9 Software User Manual Download Page 22

3–6 • Encoder Configuration

TES9 Software User Manual (Iss. 04)

Main TES9Set Menu

After the settings are downloaded from the encoder, the main TES9Set menu, similar to the one 
shown below, displays.

Main TES9Set Menu

The following is a brief description of the controls on the main TES9Set menu.

ID Area

The ID area of the menu displays general information about the encoder being configured. The 
Encoder Type and Serial Number fields describe the encoder's hardware, while the Firmware 
Number and Revision fields describe the software that is currently running on the encoder.

TCP/IP Area

This area is for display purposes only; to change any of the values, select the 

Properties

 button.

•

Address

 — The IP address of the encoder when it was powered up.

•

Netmask

 — The Netmask used by the encoder. The IP Address and Netmask are 

assigned to the encoder so that it can communicate over a TCP/IP network with other 
computers. The IP Address and Netmask values are controlled by your network 
administrator. 

•

Gateway

 — The IP address of the gateway for the network to which the encoder is 

connected. The gateway allows the encoder and other devices on the network to 
communicate with the devices outside the network. Its address is controlled by your 
network administrator.

•

DHCP

 — This feature (Dynamic Host Configuration Protocol) allows the encoder to get 

an IP address, netmask, and gateway address assigned to it by a DHCP server, as opposed 
to using fixed values. 

ON

 indicates DHCP is used and 

OFF

 indicates that the encoder is 

Summary of Contents for TES9





































































Reviews:

No comments

Brands by name

Popular brands

Load more brands