Synergy Q/MD Engineering Manual (v9.1 MD)
Preliminary Cabling and Video Installation • 4–3
Control Cable Installation
Use the following procedure to install the control cable between the electronics frame and the control
panel:
Synergy Q/MD Frame to Synergy 1 Control Panel Interconnection
Synergy Q/MD Frame to Synergy 2.5 Control Panel Interconnection
1. Ensure that you have the correct
8-pin
shielded Telco cable, with
RJ-45
,
8-pin
connectors at each end. Because of their small size, all Telco connectors look quite
similar.
2. Using an 8-pin shielded Telco cable, connect the communications port labeled
PANEL
(on the electronics frame) to the communications port labeled
FRAME
(on the rear of
the control panel).
This completes the procedure for installing the control cable between the electronics frame and the
control panel.
Please note:
•
The maximum cable length is 1000 feet (305 meters).
•
The cable must be run in accordance with good engineering practice. Ensure that there is
sufficient room for the cable and that enough slack is left in the cable run to permit long,
gentle bends. Always install cables so that they will not be subjected to physical abuse.
16
15
14
13
12
11
10
9
8
7
6
5
4
3
1
2
16
15
14
13
12
11
10
9
8
7
6
5
4
3
1
2
16
15
14
13
12
11
10
9
8
7
6
5
4
3
1
2
REF
LOOP
LOCK
CPU
100-120V~ 220-240V~ 47-63Hz
9A 650W (Canada 120V~onl
y)
LAN1
10/100 10/100
LAN2
GP I/O
P
ERIPH
1
P
ERIPH
2
P
ERIPH
3
P
ERIPH
4
P
ANEL
USB
LTC
A
B
E
OUT
C
IN
D
IN
PS 2
PS 1
1
2
MAXIMUM
RATING
1950W
MD L
IVE
P
R
ODUCTION
ENGINE
FRAME
REMOTE 1 REMOTE 2 REMOTE 3 REMOTE 4 REMOTE 5
TALLY
16
15
14
13
12
11
10
9
8
7
6
5
4
3
1
2
16
15
14
13
12
11
10
9
8
7
6
5
4
3
1
2
16
15
14
13
12
11
10
9
8
7
6
5
4
3
1
2
REF
LOOP
LOCK
CPU
100-120V~ 220-240V~ 47-63Hz
9A 650W (Canada 120V~onl
y
)
LAN1
10/100 10/100
LAN2
GP I/O
P
ERIPH
1
P
ERIPH
2
P
ERIPH
3
P
ERIPH
4
P
ANEL
USB
LTC
A
B
E
OUT
C
IN
D
IN
PS 2
PS 1
1
2
MAXIMUM
RATING
1950W
MD L
IVE
P
R
ODUCTION
ENGINE
8
1
2
3
4
7
6
5
4
3
2
1
REMOTE
TALLY
2
1
FRAME
AUX
Summary of Contents for Synergy MD
