Synergy 1 and Synergy 100 Maintenance Guide (v16-S1)
Calibration and Diagnostics • 9–27
4. Press and hold down the following three buttons to exit the panel Diagnostic Mode:
•
SEL
in the
Effects Control
Group
•
SEL
in the
Mattes
Group
•
SEL
in the
System Control
Group
This completes the procedure to test the positioner of the Synergy 100 control panel. If you are unsure
about the results of the test, or think that the results are incorrect, contact Ross Video Technical
Support.
Button and Lamp Test
The
Button Test
allows you to test all pushbuttons and LEDs on the Synergy 100 control panel.
Use the following procedure to test the Synergy 100 control panel buttons and LEDs:
1. Press and hold down the following three buttons at once:
•
SEL
in the
Effects Control
Group
•
SEL
in the
Mattes
Group
•
SEL
in the
System Control
Group
A message will scroll across the 3 four-character displays in the
Effects Control
,
Mattes
, and
System Control
groups. The message advises you that the control panel is
in Diagnostic Mode. This message will continue to scroll until a knob, button, the fader,
or the joystick is disturbed.
2. Test the
Buttons
and
LEDs
on the Synergy 100 control panel as follows:
•
Press and hold down the button you want to test. The number of the button will be
shown in the
System Control
area of the display, and the word
down
should be
shown in the
Mattes
area of the display.
•
Release the button and the word
up
should be shown in the
Mattes
area of the
display.
•
Each time you press the button, the LEDs in that
group
, or on that crosspoint
bus
,
will cycle to the next color LED. Typically, this is the green LEDs, followed by the
red LEDs, and then the orange LEDs. If the group does not contain all colors of
LEDs, only the available colors will be cycled through.
3. Press and hold down the following three buttons to exit the panel Diagnostic Mode:
•
SEL
in the
Effects Control
Group
•
SEL
in the
Mattes
Group
•
SEL
in the
System Control
Group
This completes the procedure to test all pushbuttons on the Synergy 100 control panel. If you are
unsure about the results of the test, or think that the results are incorrect, contact Ross Video Technical
Support.
Summary of Contents for Synergy 1
