background image

SRA-8802 User Manual (Iss. 04)

Service Information • 6–3

Warranty and Repair Policy

The SRA-8802 is warranted to be free of any defect with respect to performance, quality, 
reliability, and workmanship for a period of FIVE (5) years from the date of shipment from our 
factory. In the event that your SRA-8802 proves to be defective in any way during this warranty 
period, Ross Video Limited reserves the right to repair or replace this piece of equipment with a 
unit of equal or superior performance characteristics.

Should you find that this SRA-8802 has failed after your warranty period has expired, we will 
repair your defective product should suitable replacement components be available. You, the 
owner, will bear any labor and/or part costs incurred in the repair or refurbishment of said 
equipment beyond the FIVE (5) year warranty period.

In no event shall Ross Video Limited be liable for direct, indirect, special, incidental, or 
consequential damages (including loss of profits) incurred by the use of this product. Implied 
warranties are expressly limited to the duration of this warranty.

This User Manual provides all pertinent information for the safe installation and operation of 
your openGear Product. Ross Video policy dictates that all repairs to the SRA-8802 are to be 
conducted only by an authorized Ross Video Limited factory representative. Therefore, any 
unauthorized attempt to repair this product, by anyone other than an authorized Ross Video 
Limited factory representative, will automatically void the warranty. Please contact Ross Video 
Technical Support for more information.

In Case of Problems

Should any problem arise with your SRA-8802, please contact the Ross Video Technical Support 
Department. (Contact information is supplied at the end of this publication.)

A Return Material Authorization number (RMA) will be issued to you, as well as specific 
shipping instructions, should you wish our factory to repair your SRA-8802. If required, a 
temporary replacement frame will be made available at a nominal charge. Any shipping costs 
incurred will be the responsibility of you, the customer. All products shipped to you from Ross 
Video Limited will be shipped collect. 

The Ross Video Technical Support Department will continue to provide advice on any product 
manufactured by Ross Video Limited, beyond the warranty period without charge, for the life of 
the equipment.

Summary of Contents for SRA-8802













































Reviews: