Ross Opengear UDC-8625A Series User Manual Download Page 144

Page: 144 / 174

10–4 • Appendix B. Specifications

UDC-8625A Series User Manual (Iss. 11)

UDC-8625A-A Technical Specifications

This section includes the technical specifications table for the UDC-8625A-A.

Table 10.2 UDC-8625A-A Technical Specifications

Category

Parameter

Specification

Rear Modules

Supported Rear Modules

8320AR-053A, 8320AR-053B

Serial Digital

Video Inputs

Number of Inputs

Data Rates and SMPTE Standards
Accommodated

480i 59.94Hz (SMPTE 259M)

576i 50Hz (SMPTE 259M)

1080i 59.94Hz (SMPTE 292M)

1080i 50Hz (SMPTE 292M)

720p 59.94Hz (SMPTE 292M)

720p 50Hz (SMPTE 292M)

1080p Level A 59.94Hz (SMPTE 424M)

1080p Level A 50Hz (SMPTE 424M)

Impedance

75ohm terminating

Return Loss

>15dB to 1.5GHz, >10dB to 3GHz

Equalization (using Belden 1694A cable)

SD: 120m

HD: 100m

3G: 50m

Serial Digital

Video Outputs

Number of Outputs

Impedance

75ohm

Return Loss

>15dB to 1.5GHz, >10dB to 3GHz

Signal Level

800mV ±10%

DC Offset

0V ±50mV

Rise and Fall Time (20-80%)

SD: 900ps typical

HD: 150ps typical

3G: 130ps typical

Overshoot

<10% typical

AES I/O

Number of Inputs/Outputs

8 connections

AES Standards Accommodated

AES-3id-2001

Impedance

75ohm

Minimum Input

30mV

Maximum Input

2.5Vp-p

Minimum Audio Delay

2.3ms (SRC is enabled)

Summary of Contents for Opengear UDC-8625A Series















































































































































































Search results

Summary of Contents for Opengear UDC-8625A Series

Reviews:

Ross Opengear UDC-8625A Series, User Manual, Page: 144 / 174

Search results

Summary of Contents for Opengear UDC-8625A Series

Reviews: