2.
Use the left knob to select the network port that
you want to set to DHCP. Only one port can be set
to DHCP at a time.
•
1-Mode
— network port 1
•
2-Mode
— network port 2
3.
Press the
Edit
knob.
4.
Use the
Value
knob to select
DHCP
.
5.
Press the
Value
knob.
6.
Press the
Reboot
knob to restart the switcher in
DHCP mode.
The switcher will request an IP address when it
restarts.
To Set a Static IP Address
You must have the switcher connected to a network
to be able to set a static IP. If the switcher is not
connected to a network, the switcher does not display
the IP address.
Note:
Ensure that DIP switch 3 on the frame is set in the up
position. If this DIP switch is set in the down position, the IP
address is fixed at 192.168.0.123. Ensure that DIP switch 3
on the frame is set in the up position. If this DIP switch is set in
the down position, the IP address is fixed at 192.168.0.123.
1.
Press
MENU
>
System
>
NEXT
>
NEXT
>
FrmIP Addr
.
2.
Use the left knob to select the network port that
you want to set a static IP address for.
•
1-Mode
— network port 1
•
2-Mode
— network port 2
3.
Press the
Edit
knob.
4.
Use the
Value
knob to select
Static
.
5.
Press
NEXT
.
6.
Use the left knob to select
1-Addr
for port 1 or
2-
Addr
for port 2.
a)
Use the
Field
knob to select the segment in
the address that you want to change.
b)
Use the
Value
knob to select the new value
you want to use for that segment.
7.
Use the left knob to select
1-Mask
for port 1 or
2-
Mask
for port 2.
a)
Use the
Field
knob to select the segment in
the mask that you want to change.
b)
Use the
Value
knob to select the new value
you want to use for that segment.
8.
Use the left knob to select
Gatwy
.
a)
Use the
Field
knob to select the segment in
the gateway that you want to change.
b)
Use the
Value
knob to select the new value
you want to use for that segment.
9.
Press the
Gatwy
knob.
10.
Press the
Reboot
knob to restart the switcher in
with the new static IP address.
Panel Network Setup
The Carbonite Black control panel comes from the
factory set with a static IP address (192.168.0.129) but
can be set to use DHCP to automatically obtain an IP
address.
The control panel is automatically discovered in
DashBoard and appears as
CarbonitePanel
followed
by the MAC address of that particular panel.
Tip:
If you do not know the IP address of the control panel,
you can set DIP switches on the panel to lock the IP address
of the panel to 192.168.0.129 and the IP address that it
expects the frame at to 192.168.0.123. The panel must be re-
started for the new IP address to be applied. Refer to
on page 46 for DIP settings.
To Configure the Network Setting
1.
Double-click on the
CarbonitePanel
node and
click on the
Ethernet
tab.
Note:
The
Current DIP Switch
field shows the state of
the DIP1 and DIP2 switches on the control panel. Some
settings do not allow you to change the IP settings from
DashBoard.
2.
Click a
Method
button to select whether to use a
static IP address (
Static
), or obtain an IP address
(
DHCP
).
3.
For a static IP address, enter the IP address (
IP
Address
), subnet mask (
Subnet Mask
), and
gateway (
Default Gateway
) you want to use.
4.
In the
Carbonite IP Address
field, enter the IP
address of the frame you are connecting to.
5.
Click a
Panel ID
button to select whether you
want to assign the panel as the master panel
(
Master
), or one of the satellite panels (
Sat. 1
or
Sat. 2
). The panel id sets what permissions the
control panel has to the resources on the frame.
6.
Click
Apply Changes
.
To Assign a Custom Name
The name appears in the tree view in DashBoard and
allows you to easily identify your particular device.
Carbonite Black Setup Manual (v14.0) — Network Connections •
15
