manualshive.com logo in svg

Ross Abekas Mira, Manual

Share
Download
Ross Abekas Mira Manual Download Page 55

Replay Setup

To operate the server as a replay server you must
configure channels in a replay (ISO) mode, connect a
Control Surface, and open a replay event. Depending on
the replay (ISO) mode you have selected, and the number
of channels in your server, you can run both server and
replay operations at the same time.

Control Surface Connection

The Control Surface connects to the server over a
standard CAT5 ethernet cable. The cable provides both
communications and power (PoE - Power over Ethernet).
Refer to the QuickStart poster than came with your
system for cabling details.

You can connect up to two users to the 8-Channel Mira.
The 4-Channel Mira can only support a single user. When
setting up the second user you must extend the Windows

®

desktop to a second monitor attached to the server for
the second user. An additional Control Surface can be
connected to one of the available ethernet ports on the
server but a PoE injector must be used to provide power
for the unit.

To operate with two users you can either share a single
replay event between the two, or create two separate
replay events.

Note:

If you want to use a keyboard with the second Control

Surface, connect it to the USB port on the Control Surface,
instead of to the server.

Server Setup for Replay

You must configure the hardware channels for one of
the ISO modes that meet your requirements. This
configuration is based on the number of channels you
have and how you want to use them. Use the information
in the following table to pick a mode.

Playout Channels

Cameras

4-Channel

2

2

IOS2

1

3

IOS3

0

4

IOS4

8-Channel

2

2

IOS2 ×2

1

3

IOS3 ×2

0

4

IOS4 ×2

2

5

IOS5

2

6

IOS6

Playout Channels

Cameras

1

7

IOS7

0

8

IOS8

2 (3D)

2 (3D)

3D IOS2

1 (3D)

3 (3D)

3D IOS3

Note:

You can configure the 8-Channel server for two users by

creating a second replay event with channels you aren't using
in the first replay event, or you can share a single replay event
across both Control Surfaces. You must pick an ISO mode with
enough total channels to meet your needs.

To Configure the Server for Replay

Configure the server channels for the required ISO mode
and assign channels to a Control Surface.

Note:

You must connect the Control Surface to the server before

you try to configure the server. The server will detect the Control

Surface and allow you to assign channels to them.

1.

Launch the Mira Config application.

You may be prompted to allow the program to make
changes on the computer, click

Yes

.

2.

Click the

Channels

tab.

3.

Select the ISO mode for the number of cameras and
playout channels that you require.

Tip:

With the 8-Channel server you can configure both

groups of channels (ChA-D, ChE-H) to separate ISO modes
for use by separate users.

4.

Click

Apply

.

5.

Click the

Control Panel

tab.

6.

In the

Number of control panels assigned to

this Mira

field, enter the number of Control

Surfaces you want to use.

Mira Manual (v6.1) — Replay Setup •

55

Summary of Contents for Abekas Mira










































































Reviews:

No comments

Brands by name

Popular brands

Load more brands