Ross Abekas Mira, Manual

Page: 22 / 73

frames) in the
ENTRY
field and press
RUN
TIME (9)
.
6.
Select the type of transition you want to use to go
to the next clip in the Play List. They current
transition
• Dissolve — press TRANS (5) to toggle to MIX
in the Play List table.
•
Cut — press
TRANS (5)
to toggle to
MIX
in
the Play List table.
7.
Adjust the dissolve rate (mix duration) if required.
• Use the keyboard to enter a new duration for the
transition in the
ENTRY field and press MIX
DUR (6)
.
Important: The Play List must be using two
playout channels to be able to perform a dissolve
(mix) transition between clips.
8.
Set a different behaviour for the start (
@START
)
of a clip if required.
•
Play
— press @START (7) to toggle to PLAY
in the Play List table. The clip plays out
automatically when the playlist transitions to this
clip in ON-AIR mode. This is the default setting.
• Pause — press @START (7) to toggle to
PAUSE
in the Play List table. The clip is paused
on the first frame when the Play List transitions
to this clip.
9.
Set a different behaviour for the end (
@END
) of a
clip if required.
•
Take
— press @END (8) to toggle to TAKE in
the Play List table. The Play List transitions to
the next clip.
•
Pause
— press @END (8) to toggle to PAUSE
in the Play List table. The clip is paused on the
last frame when it reaches the end of the clip.
You must press
TAKE
to transition to the next
clip.
•
Loop — press
@END (8)
to toggle to
LOOP
in the Play List table. The clip is looped when it
reaches the end. You must click
TAKE to
transition to the next clip immediately or toggle
LOOP
off in the
PLAY BACK
area.
•
Play — press
@END (8)
to toggle to
PLAY
in
the Play List table. The out-point of the clip is
ignored and the clip will continue playing until
it is stopped or reaches the end. You must click
TAKE to transition to the next clip immediately.
Note: The Play List will ignore the @END command while
the loop ( ) flag is set. You must either toggle LOOP off
to proceed to the @END of the clip, or press TAKE to
transition to the next clip in the Play List.
To Copy and Paste Play List Items
An item can be cut of copied from one Play List and
pasted into another. Deleted items can also be copied
from the Trash Can and copied and pasted back into a
Play List.
1.
Press PLAY LIST > Edit Item Flags (10) > PLAY
LIST Library (1)
.
2.
Select the Play List that you want to copy an item
from and press
LOAD PLAY LIST (1) .
Tip: The Trash Can item at the bottom of the list stores
deleted (cut) clips.
3. Select the item that you want to copy.
4.
Press
CUT (7)
or
COPY (8)
to put the item onto
the clipboard.
Tip: If you want to copy and paste items within the same
Play List you can skip to the last step and paste the item
in the new position within the same list.
5.
Press
Edit Item Flags (10)
>
PLAY LIST Library
(1) .
6. Select the Play List that you want to paste the item
to and press
LOAD PLAY LIST (1) .
7. Select where in the Play List you want to paste the
item.
• Paste Before — select the item you want to paste
the new item before and press SHIFT > PASTE
(9)
.
• Paste After — select the item you want to paste
the new item after and press
PASTE (9)
.
To Enable Aux Audio for a Play List
You can create an aux audio list that overwrites the clip
audio and plays simultaneously with the clips as the Play
List is aired.
Note: Aux Audio will always play at 100% speed, even if the
video is playing at a different speed.
1.
Press PLAY LIST > SHIFT > AUDIO CONTROL
(10)
.
The playout channel goes into PL EDIT mode.
22 • Replay — Mira Manual (v6.1)