background image

2

Synergy Display Replacement Installation Guide

Ross Part Number: 

4800DR-350-01

 

Release Date: March 22, 2011. Printed in Canada.

The information contained in this guide is subject to change without notice or 
obligation.

Copyright

© 

2011

 Ross Video Limited

. All rights reserved.

Contents of this publication may not be reproduced in any form without the 
written permission of Ross Video Limited. Reproduction or reverse engineering 
of copyrighted software is prohibited.

Patents

This product is protected by the following US Patents: 4,205,346; 5,115,314; 
5,280,346; 5,561,404; 7,034,886; 7,508,455; 7,602,446; 7,834,886. This 
product is protected by the following Canadian Patents: 2039277; 1237518; 
1127289. Other patents pending.

Notice

The material in this guide is furnished for informational use only. It is subject to 
change without notice and should not be construed as commitment by Ross 
Video Limited. Ross Video Limited assumes no responsibility or liability for 
errors or inaccuracies that may appear in this guide.

Trademarks

 is a trademark of Ross Video Limited.

Ross, ROSS, ROSS ®, MLE, Vision, and Octane are registered or 
unregistered trademarks of Ross Video Limited.

All other product names and any registered and unregistered 
trademarks mentioned in this guide are used for identification 
purposes only and remain the exclusive property of their 
respective owners.

Summary of Contents for 4800DR-350-01













Reviews: