Setting
To set, press and release the desired function, and within 5 seconds
set the time with and buttons.
and buttons.
The + and - buttons increase or decrease the time at a speed depending
on how long the button is pressed.
Setting the time
Press any two buttons manualat the same time, and or button
to set the desired time. This deletes any previously set programme.
The contacts are switched off .
Manual use
By pressing the manual button the relay contacts switch on, the AUTO
symbol switches off and the saucepan symbol lights up.
Manual operation can only be enabled after the automatic programme
is over or it has been cancelled.
Automatic use
Press the cooking time or end time button to switch automatically from
the manual to the automatic function.
Semi-automatic use with cooking time setting
Press the cooking time button and set the desired time with or .
The AUTO and cooking time symbols light up continuously. The relay
switches on immediately. When the cooking end time corresponds to
the time of day, the relay and cooking time symbol switch off, the
sound signal rings and the AUTO symbol flashes.
Semi-automatic use with end time setting
Press the end time button. The time of day appears on the display.
Set the cooking end time with button. The AUTO and cooking time
symbols light up continuously. The relay contacts switch on. When
the cooking end time corresponds to the time of day, the relay and
the cooking time symbol switch off. When the cooking time is up, the
AUTO symbol flashes, the sound signal rings and both the relay and
the cooking time button switch off.
The interior glass of the oven
The interior glass of the oven door can be removed:
with the door in a semi-open position, remove the screws
A
and
B
and the profime
C
as shown in fig. 9
Use both hands to remove the glass as shown in figures 9A.
After cleaning, refit the glass by proceeding in reverse order.
Before cleaning the appliance
, disconnect the gas general tap
and unplug the appliance or disconnect power at the main circuit
breaker of the electrical system
.
Do not clean the appliance surfaces when still hot.
Do not use steam cleaners to clean the oven.
IMPORTANT
Periodically check the external gas connection hole and replace
it when it shows any sign of deterioration. Do not attempt to
repair the gas hose under any cincumstances.
ENAMELLED SURFACES
Clean with a damp sponge using soap and water.
Grease can be easily removed using hot water or a specific cleansing
agent for enamelled surfaces. Do not use abrasive cleansers.
Do not leave any acid or alkaline substances (lemon juice, vinegar,
salt, etc.) on the enamel.
Clean the parts in stainless steel with specific cleansers for stainless
steel surfaces.
These detergents must be applied using a soft cloth.
GRIDS AND BURNERS
To clean the work-top burners, remove them by pulling upwards and
soak them for about 10 minutes in hot water with a little detergent.
After having cleaned and washed them, wipe them carefully.
Make sure that no burner hole is clogged.
Clean the burners once a week or more frequently if necessary.
MAKE SURE YOU HAVE ASSEMBLED THE BURNERS IN A RIGHT
WAY.
GB
5
Start programme and check
The programme starts 4 seconds after it has been set.
The programme can be checked at any time by pressing the
corresponding button.
Setting error
A setting error is made if the time of day on the clock falls within the
cooking start and end times.
To correct the setting error, change the cooking time or cooking end
time.
The relays switch off when a setting error is made.
Cancelling a setting
To cancel a setting, press the cooking time button and then press the
- button until 00 00 appears on the display.
A set programme will automatically cancel on completion.
Minute timer
Cooking time
Cooking end
Manual
Subtract time
Add time
A
U
T
O
Fig. 4
Display
4-figures, 7-segments diplay for cooking times and time of day.
Cooking time and manual function
=
saucepan symbol
Automatic function
=
AUTO
Minutes counter
=
bell symbol
The symbols light up when the corresponding functions are selected.
LED PROGRAMMER (Fig. 4)
Features
24 hours clock with automatic programme and minutes counter.
Functions
Cooking time, cooking end time, manual position, clock,
minutes counter, times to be set up to 23 hours 59 minutes.
INSTRUCTIONS FOR USE OF CONTROL DEVICES
OVEN
Clean the enamelled parts with a damp sponge using soap and water.
Grease can be easily removed using hot water or a specific cleansing
agent for enamelled surfaces.
Do not use abrasive cleansers.
CARE AND MAINTENANCE
When the set time is up, the sound signal rings and the bell symbol
switches off.
Sound signal
The sound signal starts at the end of a programme or of the minutes
counter function and it lasts for 15 minutes.
To stop it, push any one of the functions buttons.
Automatic use with cooking time and end time setting
Press the cooking time button and select the length of the cooking
time with or button. The AUTO and cooking time symbols light
up continuously. The relay switches on. By pressing the cooking end
time button the next cooking end time appears on the display. Set the
cooking end time with button. The relay and the cooking time symbol
switch off.
The symbol lights up again when the time of day corresponds to the
cooking start time. When the cooking time is up, the AUTO symbol
flashes, the sound signal rings, the cooking time symbol and the relay
switch off.
Minutes counter
Press the minutes counter button and set the cooking time with
or button.
The bell symbol lights up when the minutes counter is operating
