Rosemount 3107 Reference Manual Download Page 95

Page: 95 / 148

Reference Manual

00809-0200-4840, Rev BA

Section 5: Service and Troubleshooting

December 2014

Section 5: Service and Troubleshooting

5.5.2

Level / Secondary Variable (SV) (D901)

This indicates the live level measured by the transmitter. In HART terminology, SV is the
Secondary Variable.

Note



Figure 4-1 on page 37

shows this parameter in a tank geometry illustration.



Units are in meters, feet, or inches depending on base units (see

page 20

Field Communicator or AMS

To view the live level measurement:

From the

Home

screen, select 1: Overview.

Select 2: Primary Purpose Variables.

Select 2: Level (SV) D901.

When finished, press EXIT to exit to the previous menu.

Note



SV is also available at the Fast Key sequence 3, 2, 1, 2
(see

Appendix D: Field Communicator

for a full menu map).

Rosemount 3490 Series Control Unit

To view the live level measurement:

From the

Main Menu

screen, select MONITOR.

Select the transmitter (e.g. “

Tx1: 3107

”).

Select READINGS.

Select VARIABLES.

Select Level (SV).

When finished, press the ESC key to exit to the previous menu.

Fast Keys

1, 2, 2

Level (SV) D901
36.540 ft

EXIT

HELP

(Field Communicator Screen)

Level (SV) D901

9.3104ft

(Rosemount 3491 Screen)

Summary of Contents for 3107





















































































































































Search results

Summary of Contents for 3107

Reviews:

Related manuals for 3107

Brands by name

Popular brands

Rosemount 3107, Reference Manual

Search results

Summary of Contents for 3107

Reviews:

Related manuals for 3107

Brands by name

Popular brands