manualshive.com logo in svg

Rosemount 3051S Series, Reference Manual

Share
Download
Rosemount 3051S Series Reference Manual Download Page 77

69

Reference Manual 

00809-0100-4803, Rev GA

Installation

September 2017

Installation

LCD display rotation

In addition to housing rotation, the optional LCD display can be rotated in 90° increments by squeezing 
the two tabs, pulling out, rotating and snapping back into place.

Note

If LCD display pins are inadvertently removed from the feature board, re-insert the pins before snapping 
the LCD display back into place.

Field terminal side of housing

Mount the transmitter so the terminal side is accessible. Clearance of 0.75-in. (19 mm) is required for 
cover removal. Use a conduit plug in the unused conduit opening if the optional Process Temperature 
Input is not installed.

Feature board side of housing

Provide 0.75-in. (19 mm) of clearance for units without an LCD display. Three inches of clearance is 
required for cover removal if an LCD display is installed.

Cover installation

Always ensure a proper seal by installing the housing covers so that metal contacts metal in order to 
prevent performance degradation due to environmental effects. For replacement cover O-rings, use 
Rosemount O-rings (part number 03151-9040-0001).

Conduit entry threads

For NEMA

®

 4X, IP66, and IP68 requirements, use thread seal (PTFE) tape or paste on male threads to 

provide a watertight seal. 

Cover jam screw

For transmitter housings shipped with a cover jam screw, as shown in 

Figure 3-3 on page 70

, the screw 

should be properly installed once the transmitter has been wired and powered up. The cover jam screw is 
intended to prevent the removal of the transmitter cover in flameproof environments without the use of 
tools. Follow these steps to install the cover jam screw:

1. Verify the cover jam screw is completely threaded into the housing. 

2. Install the transmitter housing covers and verify that metal contacts metal in order to meet 

flameproof/explosion-proof requirements. 

3. Using an M4 hex wrench, turn the jam screw counterclockwise until it contacts the transmitter cover. 

4. Turn the jam screw an additional 

1

/

2

 turn counterclockwise to secure the cover. Application of 

excessive torque may strip the threads.

5. Verify the covers cannot be removed.

Summary of Contents for 3051S Series































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands