manualshive.com logo in svg

Rosemount 3051S Series, Reference Manual

Share
Download
Rosemount 3051S Series Reference Manual Download Page 35

27

Reference Manual 

00809-0100-4803, Rev GA

Configuration

September 2017

Configuration

2.6

Detailed device configuration 

2.6.1

Model identification

The

 Identification 

tab displays the device identification information on one screen. The fields with white 

backgrounds may be edited by the user.

Figure 2-19. Device - Identification Tab

2.6.2

Alarm and saturation

The Rosemount 3051SMV automatically and continuously performs self-diagnostic routines. If the 
self-diagnostic routines detect a failure, the transmitter drives the output to the configured alarm value. 
The transmitter will also drive the output to configured saturation values if the primary variable goes 
outside the 4–20 mA range values.

The alarm and saturation settings can be configured using Engineering Assistant, AMS Device Manager, 
or a Field Communicator. See 

“Alarm and saturation level configuration” on page 28

 for more 

information. The alarm direction can be configured using the hardware switch on the feature board. See 

“Configure security (write protect)” on page 67

 for more information on the hardware switch.

The Rosemount 3051SMV has three options for alarm and saturation levels:

Rosemount (Standard), see 

Table 2-4 on page 28

NAMUR, see 

Table 2-5 on page 28

Custom (user-defined), see 

Table 2-6 on page 28

Mass and energy flow Fast Keys

1, 3, 5

Direct process variable output Fast Keys

1, 3, 5

Summary of Contents for 3051S Series































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands