background image

Reference Manual 

300550en, Rev AA
December 2010

4-11

Rosemount 2240S

Section 4. 2240S Installation

4.4.8

Tankbus Wiring

Follow this procedure to connect the Rosemount 2240S:

1. Ensure that the power supply is switched off.
2. Loosen the four screws and remove the cover on the terminal 

compartment.

Figure 4-4. 2240S terminal 

compartment

3. Run the Tankbus wires through the appropriate cable glands or conduits. 
4. Connect the Tankbus wires to the X2 and X3 terminals as shown in 

Figure 4-4.

5. Connect the cable shield to the terminal marked X1.
6. Use metal plugs to seal unused ports.
7. In order to prevent water from entering the terminal compartment, ensure 

the cover sealing is placed in the correct position

8. Attach and tighten the cover on the terminal compartment. Ensure that 

the cover is fully engaged to meet explosion-proof requirements and to 
prevent water from entering the terminal compartment.

9. Tighten the conduit/cable glands. Note that adapters are required for 

M20 glands

NOTE!

Ensure that o-rings and seats are in good condition prior to mounting the 
cover in order to maintain the specified level of ingress protection. The same 
requirements apply for cable inlets and outlets (or plugs). Cables must be 
properly attached to the cable glands.

Daisy-chain connection 

to other field devices

(page 4-12)

X2: Tankbus (+) output

X3: Tankbus (-) output

Jumper to 

invoke built-in 

termination

X4: Tankbus 

terminator

X1: Cable Shield

X2: Tankbus (+) input

X3: Tankbus (-) input

Internal grounding 

terminals

Cable glands for 

Tankbus wires and 

temperature elements

Summary of Contents for 2240S





































































































Reviews: