Rose electronics Orion XC OXS-XC008-FS Installation And Operation Manual Download Page 77

Page: 77 / 132

Orion XC Installation and Operation Manual

Loading Internal Configuration through the Java Tool

Figure 70. Loading Internal Configuration through the Java Tool

To load the configuration from the internal matrix memory, proceed as follows:

1. Select

Administration > Activate Configuration

during online-mode in the task area.

2. Select the required configuration.

3. Load the configuration by pressing the

Activate

button.

Saving of Configurations (External)

Configurations can also be saved as files which are stored outside of the matrix. This menu can only be

accessed from the Java Tool.

Figure 71. Saving External Configuration through the Java Tool

Summary of Contents for Orion XC OXS-XC008-FS





































































































































Search results

Summary of Contents for Orion XC OXS-XC008-FS

Reviews:

Related manuals for Orion XC OXS-XC008-FS

Brands by name

Popular brands

Rose electronics Orion XC OXS-XC008-FS, Installation And Operation Manual

Search results

Summary of Contents for Orion XC OXS-XC008-FS

Reviews:

Related manuals for Orion XC OXS-XC008-FS

Brands by name

Popular brands