background image

10-00609   REV D 

III 

WARRANTY 

 

 
ROS,  Inc.  (hereinafter  called  "

ROS

")  warrants  its  products  as  stated  below  subject  to  the 

conditions specified. 
  

ROS

 warrants its products, when operated under normal conditions, to be free from defects in 

material  or  workmanship  for  a  period  of  one  year  from  the  date  of  purchase  provided  that 
inspection by 

ROS

 discloses that such defects developed under normal and proper use.  

ROS

 

products  repaired  or  replaced  pursuant  to  this  warranty  shall  be  warranted  for  the  unexpired 
portion of the warranty applying to the original product.  The liability of 

ROS

 under this warranty 

shall exist subject to the following conditions: 
 

(a) 

Purchaser  properly  notifies  ROS  of  such  defects  and  the  defective  product  is 
returned to ROS, transportation charges paid by Purchaser. 

 
(b) 

ROS shall be released from all obligations under its warranty in the event repairs 
or modifications are made by persons not authorized by ROS. 

 
(c) 

Representations  and  warranties  made  by  any  person,  including  distributors  and 
representatives  of  ROS,  which  are  inconsistent or  conflict  with  the  terms  of this 
warranty, shall not be binding upon ROS unless reduced to writing and approved 
by  an  officer  of  ROS.    ROS  shall  in  no  event  be  liable  for  other  direct,  special, 
incidental, consequential, indirect or penal damages. 

 
(d) 

The laws of the State of California shall govern this warranty. 

 
In the event the defect is determined to be within the terms of this warranty then 

ROS

 agrees to 

repair  and/or  replace  (at 

ROS

'  discretion)  the  product  or  defective  portion  at  no  charge  to  the 

Purchaser.  This warranty does not apply to expendable items or to normal wear-and-tear, and 
is conditional upon performance of normal preventative maintenance procedures. 
 
Our  commitment to quality and customer  service directs  us to constantly strive to improve our 
products.    The  materials  and  specifications  presented  in  our  manuals  and  data  sheets  are 
correct and accurate to the best of our knowledge, and are presented in good faith.  However, 
the information is not guaranteed and is subject to change without notice. 
 

LIMITATIONS OF REMEDIES 
 

Purchaser assumes all risk and liability for results obtained in any installation, operation, or use 
of the product.  Purchaser’s sole remedy for any breach of warranty by vendor shall be limited to 
the  “express  remedies”  set  forth  above.    Otherwise,  in  no  event  shall  vendor,  its  agents,  or 
employees  be  liable  to  the  original  purchaser  or  any  third  party  for  any  consequential  or 
incidental  damages  or  expenses  of  any  nature  arising  directly  out  of  or  in  connection  with  the 
use of vendor projects, even if vendor has been advised of the possibility of such damages or 
expenses.      In  any  event,  unless  otherwise  contrary  to  state  law,  vendor  liability  under  this 
limited warranty shall not exceed the purchase price of the product

 
 

Summary of Contents for MV-LED II DC














Reviews: