Ronde & Schwarz 1424.6721K02 User Manual Download Page 98

Page: 98 / 148

Remote control commands

R&S

NRP18S-xx

User Manual 1178.3686.02 ─ 07

Query parameters:

<Item>

String

Usage:

Query only

8.12

Configuring the system

The

SYSTem

subsystem contains a series of commands for general functions that do

not directly affect the measurement.

8.12.1

Configuring general functions

SYSTem:DFPRint<Channel>?

...........................................................................................99

SYSTem:ERRor:ALL?

.......................................................................................................99

SYSTem:ERRor:CODE:ALL?

............................................................................................ 99

SYSTem:ERRor:CODE[:NEXT]?

........................................................................................99

SYSTem:ERRor:COUNt?

................................................................................................100

SYSTem:ERRor[:NEXT]?

................................................................................................100

SYSTem:FWUPdate

.......................................................................................................100

SYSTem:FWUPdate:STATus?

......................................................................................... 100

SYSTem:HELP:HEADers?

.............................................................................................. 101

SYSTem:HELP:SYNTax?

................................................................................................101

SYSTem:HELP:SYNTax:ALL?

......................................................................................... 101

SYSTem:INFO?

............................................................................................................. 101

SYSTem:INITialize

......................................................................................................... 102

SYSTem:LANGuage

.......................................................................................................102

SYSTem:LED:COLor

...................................................................................................... 102

SYSTem:LED:MODE

......................................................................................................103

SYSTem:MINPower?

......................................................................................................103

SYSTem:PARameters?

...................................................................................................103

SYSTem:PARameters:DELTa?

........................................................................................ 104

SYSTem:PRESet

........................................................................................................... 104

SYSTem:REBoot

............................................................................................................104

SYSTem:RESTart

...........................................................................................................104

SYSTem:RUTime

........................................................................................................... 104

SYSTem:SERRor?

......................................................................................................... 104

SYSTem:SERRor:LIST:ALL?

........................................................................................... 105

SYSTem:SERRor:LIST[:NEXT]?

...................................................................................... 105

SYSTem:SUTime

........................................................................................................... 105

SYSTem:TLEVels?

.........................................................................................................106

SYSTem:TRANsaction:BEGin

......................................................................................... 106

SYSTem:TRANsaction:END

............................................................................................106

SYSTem[:SENSor]:NAME

............................................................................................... 106

SYSTem:VERSion?

........................................................................................................106

Configuring the system

Summary of Contents for 1424.6721K02





















































































































































Search results

Summary of Contents for 1424.6721K02

Reviews:

Brands by name

Popular brands

Ronde & Schwarz 1424.6721K02, User Manual

Search results

Summary of Contents for 1424.6721K02

Reviews:

Brands by name

Popular brands