manualshive.com logo in svg

Ronde & Schwarz (1309.6830.02, Quick Start Manual, Page: 46 / 77

Share
Download
Ronde & Schwarz (1309.6830.02 Quick Start Manual Download Page 46

R&S ZVH 

Putting into Operation 

Configuring the R&S ZVH 

Quick Start Guide 1309.6900.12 - 06 

44 

1.6.11  Resetting the R&S ZVH 

You can either preset the R&S ZVH or reset it to factory settings. 

Presetting the R&S ZVH 

The PRESET key resets the R&S ZVH to the default setup of the currently active 
operating mode. 

This allows you to define a new configuration based on defined measurement 
parameters without parameters from a previous measurement unintentionally still being 
active. 

►  Press the PRESET key. 

Resetting the R&S ZVH 

A "Reset to Factory Settings" resets the R&S ZVH to the factory defaults. 

During a reset, the R&S ZVH restores the original configuration. It also deletes all 
customized datasets (limit lines, standards, channel tables, cable models etc.). 
Instead, it will reinstall all the datasets that have been available after delivery. 

 

 

 

 

 

 

Risk of data loss 

All datasets you have saved will be deleted during a factory reset. 

 

   

 
►  In the "Instrument Setup" dialog box, select the "Reset to Factory Settings" item. 

 

►  Press the ENTER key. 

The R&S ZVH initiates the reset procedure and shows a warning message box. 

 

Selecting "Yes" performs the reset. During the reboot, it shows a corresponding 
message. 

Selecting "No" cancels the reset. 

Summary of Contents for (1309.6830.02














































































Reviews:

No comments