FRONT PANEL DESCRIPTION
NOTE: The following descriptions are for both channels.
PWR
CLIP
CLIP
ACTIVE
ACTIVE
BOTTOM
BOTTOM
DEFINITION
DEFINITION
RSE261
CHANNEL ONE
CHANNEL TWO
ACTIVE SWITCH: Engages and disengages the RSE261 process. When out, the
effect is bypassed.
BOTTOM: Controls the low frequency cut/boost (flat or no cut/boost is at about 11
O’clock). There is a 0 to 1/2 turn spectrum spread from mid-range to bass with
this control as well as amplitude control.
DEFINITION: Controls the amount of sonic clarity and sound spread. Setting it on
0 is flat response and minimal spread, on 10 is maximum spread and definition.
This is also a good setting for constant dispersion horns.
CLIP LED: Indicates circuit overload in the channel.
PWR LED: Indicates that the RSE261 power supply is connected to an AC outlet,
and the power is turned on.
POWER SWITCH: Controls the primary power to the RSE261.
REAR PANEL DESCRIPTION
INPUT
OUTPUT
INPUT
OUTPUT
INPUTS
OUTPUTS
AC IN
12 VAC
MODEL
RSE261
MADE IN U.S.A.
2
2
1
1
1
1
2
2
AC IN: Connect to the included Rolls PS12 12 Volt AC adapter.
CH 1 - 2 , 1/4” OUTPUTS: Unbalanced outputs.
CH 1 - 2 , 1/4” INPUTS: Unbalanced inputs for connection (normally) to the last
device in the signal chain before the power amplifier.
RCA INPUTS: Unbalanced inputs.
RCA OUTPUTS: Unbalanced outputs.
OPERATION
STEREO CONNECTION
The diagram shown below is a stereo connection example for the RSE261. We
recommend you put the RSE261 last in the signal chain. If you have an EQ or
other processor after your mixer’s main outputs, insert the RP261 between it and
your crossover and/or power amplifier.
If you are connecting the RSE261 into a home stereo system, insert the Sonic
Exciter between your signal sources such as tuners, cassette players, CD players
etc. and the power amplifier.
CAUTION: TO AVOID POSSIBLE SPEAKER OR AMPLIFIER DAMAGE, ALWAYS
TURN ON THE RSE261 AND OTHER PERIPHERAL EQUIPMENT BEFORE
TURNING ON THE POWER AMPLIFIERS. ALSO TURN OFF THE POWER
AMPLIFIERS FIRST, BEFORE TURNING OFF THE RSE261 AND OTHER
EQUIPMENT.
INPUT
OUTPUT
INPUT
OUTPUT
INPUTS
OUTPUTS
AC IN
12 VAC
MODEL
RSE261
MADE IN U.S.A.
2
2
1
1
1
1
2
2
TAPE
OUT
TAPE
IN
R
L
TRIM
LINE
INSERT
MIC 1
INSERT
INSERT
INSERT
LINE
LINE
LINE
TRIM
TRIM
TRIM
TRIM
TRIM
TRIM
TRIM
PHANTOM POWER
LEFT
RIGHT
LEFT
RIGHT
LEFT
RIGHT
LEFT
RIGHT
LEFT OUT
RIGHT OUT
AUX 1
RET. RIGHT
AUX 2
OUT
AUX 1
OUT
MIC 2
MIC 3
MIC 4
MIC 5/6
MIC 7/8
MIC 9/10
MIC 11/12
+48V
OFF
+10
+60
+10
+60
+10
+60
+10
+60
+10
+60
+10
+60
+10
+60
+10
+60
AUX 2
RET. LEFT
AUX 2
RET. RIGHT
POWER
AUX 1
RET. LEFT
MADE IN U.S.A.
RISQUE DE CHOC - NE PAS ENLEVER
SERIAL NUMBER
WARNING:
To reduce the risk of electric
shock or fire do not expose
this device to rain or moisture.
CHANNEL 2 INPUT
CHANNEL 1 INPUT
BRIDGE NORMAL
OUTPUT 2
OUTPUT 1
4A 120V - 2A 230 V
OUTPUT 1
OUTPUT 2
-
-
+
+
MAINS POWER
WARNING
For continued prootection against
risk of fire, replace only with
same type and rating of fuse.
CAUTION
TO REDUCE THE RISK OF ELECTRIC
SHOCK DO NOT NOT REMOVE LID. NO
USER SERVICABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL
CORPORATION
MIXER
POWER
AMPLIFIER
3
4
