Rolls-Royce Helicon X3 User Manual Download Page 87

Page: 87 / 140

Maintenance Instructions

Page 13 of 22

Doc. No.: 13S000411
Revision: A

4.12 Replacing the Signal Isolation Amplifier

When replacing a galvanic insulated, the DIP-switch must be correctly set. Compare

with the DIP-switch on the replaced amplifier and adjust as necessary. All I/O-modules

can be replaced as is and do not need further measures.
1.

Disconnect the plugs.

2. Disengage the top part of the housing by carefully pressing the latches on both

sides (2).

3. Pull out the top part of the housing and the electronics section until the lock (3).
4. Set the input and output ranges, offset and bandwidth using DIP switches (4,5,6)

5 Adjusting the parameters

This chapter describes how to access and adjust parameters using the control panel

display.

Pos

Component

Signal isolation amplifier

Latches

Top part

DIP switch

Summary of Contents for Helicon X3

















































































































Search results

Summary of Contents for Helicon X3

Reviews:

Related manuals for Helicon X3

Brands by name

Popular brands

Rolls-Royce Helicon X3, User Manual

Search results

Summary of Contents for Helicon X3

Reviews:

Related manuals for Helicon X3

Brands by name

Popular brands