Rolls-Royce Helicon X3 User Manual Download Page 105

Page: 105 / 140

Trouble Shooting

Page 9 of 16

Doc. No.: 13S000411
Revision: A

2.5

Deviation Surveillance Alarms

The following alarms will be issued for deviation surveillance related faults:

Alarm Text

Cause, Effect and Action

PORT MP NC Pitch Deviation
Alarm

Cause: Hydraulic/Mechanical failure in pitch servo mechanism

Effect: Pitch Not moving according to order from control system

Action: Stop using thruster, check thruster mechanical manual

PORT MP NC Azimuth Deviation
Alarm

Cause: Hydraulic/Mechanical failure in azimuth servo mechanism

Effect: Azimuth not moving according to order from control system

Action: Stop using thruster, check thruster mechanical manual

PORT MP NC Start Failure

Cause: Thruster failed to start or Thruster stopped without being stopped
by operator (trip on high current, pitch deviation alarm, failure in starter/
drive).

Effect: Thruster not available.

Action: Investigate what is causing thruster to stop/not start.

Summary of Contents for Helicon X3

















































































































Search results

Summary of Contents for Helicon X3

Reviews:

Related manuals for Helicon X3

Brands by name

Popular brands

Rolls-Royce Helicon X3, User Manual

Search results

Summary of Contents for Helicon X3

Reviews:

Related manuals for Helicon X3

Brands by name

Popular brands