manualshive.com logo in svg

Roland VS-1680 V-XPANDED, User Manual, Page: 247 / 282

Share
Download
Roland VS-1680 V-XPANDED User Manual Download Page 247

247

Chapter 21 System and Global Settings

Chapter 21

7.

Press [PLAY (DISPLAY)] to return to the Playlist display. 
You must Restart the VS-1680 for the new SCSI ID 
number to become effective.

IDE Drive Switch

It is possible to use a VS-1680 with just an external hard drive 
connected to the SCSI port, without an internal hard drive. In 
such a case, it takes the VS-1680 approximately 30 seconds 
after the power is turned on just to check its internal hard 
drive connection status. If you don’t have an internal IDE 
drive installed in the VS-1680, you can avoid this wait by 
setting the VS-1680 to not attempt to use an internal IDE 
drive.

1.

Hold [SHIFT] and press [F5 (SYSTEM)]. The System 
Menu icon is displayed. If the System Menu icon does 
not appear, press [F6 (EXIT)].

2.

Press [F2 (GLOBL)]. If “GLOBL” does not appear above 
[F2], first press [PAGE] until “GLOBL” appears, and then 
press [F2 (GLOBL)].

3.

Use [

], [

], [

], and [

] to move the 

cursor to “IDE Drive.”

4.

Use the TIME/VALUE dial to change the setting for IDE 
Drive.

IDE Drive

When not using an internal hard drive, set this to “Off.” 
The default setting is “On.”

5.

Hold [SHIFT] and press [ZERO]. “STORE OK ?” appears 
in the display.

6.

Press [YES]. The current song is saved.

7.

Press [PLAY (DISPLAY)] to return to the Playlist display. 
The changed setting becomes effective the next time the 
VS-1680 is turned on.

Input Peak Level

You can designate the level at which the peak indicator lights 
based on signal input via the INPUT jacks (1-8).

1.

Hold [SHIFT] and press [F5 (SYSTEM)]. The System 
Menu icon is displayed. If the System Menu icon does 
not appear, press [F6 (EXIT)].

2.

Press [F2 (GLOBL)]. If “GLOBL” does not appear above 
[F2], first press [PAGE] until “GLOBL” appears, and then 
press [F2 (GLOBL)].

3.

Use [

], [

], [

], and [

] to move the 

cursor to “Input Peak Level.” Use the TIME/VALUE dial 
to change the setting.

Input Peak Level

This sets the volume level at which the peak indicators 
(above the Input Sens knobs) light.

CLIP:

The indicator lights when the input is at maximum 
level (distortion).

-3 dB:

The indicator lights 3 dB before the input is at 
maximum level.

-6 dB:

The indicator lights 6 dB before input is at maximum 
level.

4.

Press [PLAY (DISPLAY)] to return to the Playlist display.

Previous/Next Switch

[PREVIOUS] and [NEXT] normally move the position of the 
timeline to the beginning or end of the previous or next 
phrase on the selected track.

fig.12-18

You can change this function so [PREVIOUS] and [NEXT] 
recall markers, similar to the manner in which the track skip 
button on a CD player works.

fig.12-19

1.

Hold [SHIFT] and press [F5 (SYSTEM)]. The System 
Menu icon is displayed. If the System Menu icon does 
not appear, press [F6 (EXIT)].

2.

Press [F2 (GLOBL)]. If “GLOBL” does not appear above 
[F2], first press [PAGE] until “GLOBL” appears, and then 
press [F2 (GLOBL)].

Current Time

Current Time

M1

M2

M3

M4

M5

Summary of Contents for VS-1680 V-XPANDED



























































































































































































































































































Reviews:

No comments