Roland VariOS User Manual Download Page 29

Page: 29 / 168

Installation

Windows Me users

◆

Preparations for installing the driver

With the VariOS disconnected, start up Windows.

Exit all currently running software (applications).

Also, close any open windows. If you are using a virus checker or similar
software, be sure to exit this as well.

Prepare the CD-ROM.

Insert the CD-ROM into the CD-ROM drive of your computer.

Click the Windows

start

menu, and from the menu, select

“Run...”

Open the

“Run...”

dialog box.

In the dialog box that appears, input the following into the

“Open”

field,

and click

[OK]

D:\ENGLISH\DRIVER\USB_98ME\SETUPINF.EXE

Open the

SetupInf

dialog box.

You are now ready to install the driver.

◆

Installing the driver

Use the USB cable to connect the VariOS to your computer.

fig.02-USB

Set the VariOS’s

power switch

to the

position.

The

New Hardware Found

dialog box will appear.

Input the following into the

“Copy files from”

field, and click

[OK]

D:\ENGLISH\DRIVER\USB_98ME

Disconnect all USB cables
other than those for a USB
keyboard or USB mouse.

The drive name “D:” may
be different depending on
your system. Type the
name of your CD-ROM
drive.

USB cable

VariOS

(Rear)

Computer

USB connector

You must power up the
VariOS according to the
procedure given on p. 49.

The drive name

“D:”

may

be different depending on
your system. Type the
name of your CD-ROM
drive.

Summary of Contents for VariOS









































































































































































Search results

Summary of Contents for VariOS

Reviews:

Roland VariOS, User Manual, Page: 29 / 168

Search results

Summary of Contents for VariOS

Reviews: