Roland VariOS User Manual Download Page 18

Page: 18 / 168

Names of Things and What They Do

Restoring the factory settings (Factory Reset)

Here’s how to restore the VariOS to the factory-set condition.

Press the

[MENU]

button so it’s lighted. The MENU screen will appear.

Initially, the MENU screen will show the most recently selected menu. You need to go to the top level
menu. You can get there by pressing and continuing to hold the

[MENU]

button for a few moments

(when the

[MENU]

button is not illuminated), or by pressing the

[EXIT]

button.

Turn the

[VALUE]

knob to select “

Menu 6 Utility

,” and press the

[VALUE]

knob.

Turn the

[VALUE]

knob to select “

Menu 6-4 Factory Reset

,” and press the

[VALUE]

knob.

The display will ask “

Factory Reset OK?

,” so press the

[VALUE]

knob.

If you press the

[EXIT]

button, the Factory Reset operation will be cancelled.

This operation will not restore the internal demo song of the VariOS. Please read “Reloading the
VariOS internal demo song” (p. 140).

Summary of Contents for VariOS









































































































































































Search results

Summary of Contents for VariOS

Reviews:

Roland VariOS, User Manual, Page: 18 / 168

Search results

Summary of Contents for VariOS

Reviews: