Roland VariOS User Manual Download Page 24

Page: 24 / 168

Installation

The

Found New Hardware Wizard

will appear.

Make sure that the screen indicates

“Roland VariOS,”

select

“Install from

a list or specific location (Advanced),”

and click

[Next]

fig.2-7_20

The screen will indicate

“Please

choose your search and installation

options.”

Select

“Don’t search. I will choose

the driver to install,”

and click

[Next]

Make sure that the

“Model”

field

indicates

“Roland VariOS,”

and click

[Next]

. Driver installation will begin.

If the

“Driver Signing Options”

setting was not set to

“Ignore”

, a

“Hardware Installation”

dialog box will appear.

“Driver Signing Options”

is set to

“Warn,”

fig.2-5

Click

[Continue Anyway]

Continue the installation.

“Driver Signing Options”

is set to

“Block,”

fig.2-5a

Click

[OK]

When the

“Found New Hardware Wizard”

appears,

click

[Finish]

Using the procedure described in the

“Troubleshooting”

section

“Q. Device Manager

shows “?”, “!”, or “USB Composite Device””

(p.

143), delete the data for the VariOS that was wrongly
detected. Then install the driver using the procedure described in

“Installing the Driver”

(p. 22). When doing so, set

“Driver Signing

Options”

in step 4 to

"Ignore."

Summary of Contents for VariOS









































































































































































Search results

Summary of Contents for VariOS

Reviews:

Roland VariOS, User Manual, Page: 24 / 168

Search results

Summary of Contents for VariOS

Reviews: