
46
Chapter 4 Using the VB-99 in
Combination with an FC-300
With an FC-300 (optional) connected to the VB-99, you can perform
the following operations:
• Switch patches
• Have patch names be shown in the FC-300’s display
• Control tones with the FC-300’s pedals (Control Assign)
• Show the VB-99’s tuner in the FC-300’s display when the
TUNER function is used
• Switch the FC-300’s Amp Control on and off
Connect the VB-99 and FC-300 using the RRC2 cable included with
the unit.
What is RRC2?
RRC2 is a Roland protocol that provides for the supply of
power and two-way data communications over a single cable.
Devices can also be connected using a commercially available
ethernet cable instead of the included RRC2 cable.
• Be sure to connect the RRC2 OUT connector to a device with an
RRC2 IN connector. Use of the connection with LAN or other
devices may cause generation of heat and damage to the
equipment.
• Carefully connect the RRC2 cable the way in—until it is firmly
to the RRC2 IN connector.
• Do not subject the RRC2 cable to stress or physical shock.
• If using commercially available ethernet cable as the RRC2
connecting cable, be sure that the cable meets the following
specifications:
•
Category 5 (Cat5) or above
•
Maximum length of 15 meters
•
Cable designed for straight-through connection.
*
Ethernet cables designed for crossover connections cannot be used.
If connecting the VB-99 with an FC-300 using an RRC2 cable, make
the settings below as needed.
This sets the method for controlling the FC-300.
1.
Press [SYSTEM].
2.
Press PAGE [
] to display Page 1.
3.
Press [F5] (FC-300).
4.
Set the SYS EX MODE with [F1] (OFF/ON) or
with the F1 knob.
*
The FC-300 will not respond unless you return to the Play screen.
Connecting with the RRC2
IN Connector
Settings Related to the FC-
300
Settings for Control of the FC-
300
Available
Settings
Description
ON
When connected to the VB-99, the FC-300 automat-
ically changes to Exclusive mode and functions in
accordance with the settings made with the VB-99.
This is the setting normally selected. You can con-
trol the FC-300 even without matching the VB-99’s
and FC-300’s Device IDs.
Connecting an FC-300 automatically switches the
FC-300 to Exclusive mode. Normally, you should
select this setting.
OFF
Select OFF when using the FC-300 in a mode other
than System Exclusive mode.
The mode does not switch automatically.
VB-99_e.book 46 ページ 2008年8月18日 月曜日 午後1時10分
Summary of Contents for V-Bass 04672434
