manualshive.com logo in svg

Roland V-40HD, Owner'S Manual, Page: 25 / 60

Share
Download
Roland V-40HD Owner'S Manual Download Page 25

25

About Input/Output Formats

Using the Buttons to Change the Output Format for OUTPUT 1/2

Use the OUTPUT selectors on the top panel to change the output format. Press the [FORMAT] button to change the illuminated 
indicator.

fig.switch-output.eps

By default, the following signals are output. The signal format that is output changes according to the setting described in the 
previous section.

Frame Rate

59.94 Hz

50 Hz

SD

NTSC 

PAL

HD

1080/59.94i

1080/50i

RGB

1024 x 768/60 Hz

1024 x 768/75 Hz 

Output Formats from the Connectors

Signals in the following formats can be output from the respective output connectors on the V-40HD. Refer to Output Menu (p. 46).

OUTPUT 1/2

Frame Rate

59.94 Hz

50 Hz

COMPOSITE (*1)(*2) NTSC

PAL

COMPONENT (*2)

480/59.94p, 720/59.94p, 1080/59.94p

576/50p, 720/50p, 1080/50p

RGB (*2)

640 x 480/60 Hz, 800 x 600/60 Hz, 1024 x 768/60 Hz, 
1280 x 768/60 Hz, 1280 x 1024/60 Hz, 1366 x 768/60 Hz, 
1400 x 1050/60 Hz, 1600 x 1200/60 Hz,  
1920 x 1200/60 Hz (Reduced Blanking)

640 x 480/75 Hz, 800 x 600/75 Hz, 1024 x 768/75 Hz, 
1280 x 768/75 Hz, 1280 x 1024/75 Hz, 1366 x 768/75 Hz, 
1400 x 1050/75 Hz, 1600 x 1200/60 Hz,  
1920 x 1200/60 Hz (Reduced Blanking)

HDMI

480/59,94i, 480/59.94p, 720/59.94p, 1080/59.94i, 1080/59.94p 576/50i, 576/50p, 720/50p, 1080/50i, 1080/50p
640 x 480/60 Hz, 800 x 600/60 Hz, 1024 x 768/60 Hz, 
1280 x 768/60 Hz, 1280 x 1024/60 Hz, 1366 x 768/60 Hz, 
1400 x 1050/60 Hz, 1600 x 1200/60 Hz,  
1920 x 1200/60 Hz (Reduced Blanking)

640 x 480/75 Hz, 800 x 600/75 Hz, 1024 x 768/75 Hz, 
1280 x 768/75 Hz, 1280 x 1024/75 Hz, 1366 x 768/75 Hz, 
1400 x 1050/75 Hz, 1600 x 1200/60 Hz, 
1920 x 1200/60 Hz (Reduced Blanking)

*1 : OUTPUT 1 only
*2 : No output while the HDCP setting is ON (p. 26).

PVW OUT

Frame Rate 

59.94 Hz

50 Hz

HDMI

1920 x 1080/60 Hz

*  HDMI audio output format of OUTPUT 1/2 and PVW OUT is Linear PCM, 24 bits/48 kHz, 2ch.

Summary of Contents for V-40HD





























































Reviews:

No comments