manualshive.com logo in svg

Roland V-40HD, Owner'S Manual, Page: 24 / 60

Share
Download
Roland V-40HD Owner'S Manual Download Page 24

24

Input Formats

It is possible to input signal of various formats to INPUT 1-4 of the V-40HD.
Signals of the following formats can be input. The input format is detected automatically.

Frame Rate

59.94 Hz

50 Hz

COMPOSITE

NTSC)

PAL

COMPONENT

480/59,94i, 480/59.94p, 720/59.94p, 1080/59.94i, 1080/59.94p 576/50i, 576/50p, 720/50p, 1080/50i, 1080/50p

RGB

640 x 480/60 Hz, 800 x 600/60 Hz, 1024 x 768/60 Hz, 1280 x 768/60 Hz, 1280 x 1024/60 Hz, 1366 x 768/60 Hz, 
1400 x 1050/60 Hz, 1600 x 1200/60 Hz, 1920 x 1080/60 Hz, 1920 x 1200/60 Hz (Reduced Blanking)

HDMI

480/59,94i, 480/59.94p, 720/59.94p, 1080/59.94i, 1080/59.94p 576/50i, 576/50p, 720/50p, 1080/50i, 1080/50p
640 x 480/60 Hz, 800 x 600/60 Hz, 1024 x 768/60 Hz, 1280 x 768/60 Hz, 1280 x 1024/60 Hz, 1366 x 768/60 Hz, 
1400 x 1050/60 Hz, 1600 x 1200/60 Hz, 1920 x 1080/60 Hz, 1920 x 1200/60 Hz (Reduced Blanking) 

*  HDMI audio input format is Linear PCM, 24 bits/48 kHz, 2ch.

Using the Menus to Set the Output Format for OUTPUT 1/2

You can use the menus to the set the output format for OUTPUT 1 and 2.

*  The output signal format of the COMPOSITE connector in OUTPUT 1 is NTSC or PAL. A common format is output from the HDMI and RGB/

COMPONENT connectors in OUTPUT 1/2. 

1.  Display the Output menu.

Press the [MENU] button to display the menu. Use the [CURSOR] buttons to select [Output], then press the [ENTER] button to 
display the Output menu.

fig.open-output-menu.eps

2.  Set the output format.

Turn the [VALUE] dial to set the output format.

fig.select-out-format.eps

You can independently set various parameters for OUTPUT 1 and 2. Refer to Output menu (p. 46).

If one of below is selected as the output format, signal output from the RGB/COMPONENT connector is disabled.

• 

480/59.94i (NTSC)

• 

576/50i (PAL)

• 

1080/59.94i

• 

1080/50i

About Input/Output Formats

Summary of Contents for V-40HD





























































Reviews:

No comments