Roland V-1HD+, Reference Manual

Page: 58 / 68

58
Menu List
16: TALLY/RS-232
Menu item Value
(bold text: default value)
Explanation
TALLY
OFF,
ON
Turns the tally signal output on/off. If this is “ON,” , the tally signal is output from the TALLY
connector (p. 67).
RS-232 OFF, ON If this is “ON,” RS-232 commands can be transmitted and received.
RATE 38400, 115200 Specifies the communication speed (bps) of the RS-232 connector.
17: SYSTEM
Menu item Value
(bold text: default value)
Explanation
HDCP (*17) OFF , ON
Specifies whether HDCP is enabled or disabled. If this is “ON,” copyright-protected (HDCP) video
can be input. HDCP is also added to the video that is output.
FRAME RATE (*17) 59.94, 50Hz Specifies the frame rate.
SYSTEM FORMAT (*17) 1080p , 1080i, 720p
Specifies the system format.
* The output format is the same as the system format.
CUT SW ASSIGN (*18)
Specifies the function of the [CUT] button.
H
AUTO TAKE
When the video of the B/PST bus is selected, switches to the video of the A/PGM bus. The
transition time is specified by the TRANSITION TIME menu item “WIPE/MIX TIME.”
H
AUTO TAKE
I
Switches the video between A/PGM bus and B/PST bus. The transition time is specified by the
TRANSITION TIME menu item “WIPE/MIX TIME.”
H
CUT When the video of the B/PST bus is selected, switches to the video of the A/PGM bus as a cut.
H
CUT
I
Switches the video between A/PGM bus and B/PST bus as a cut.
H
TRANSFORM
When the video of the B/PST bus is selected, switches to the video of the A/PGM bus as a cut only
while you’re holding down the button.
AUTO SW ASSIGN
(*18)
Specifies the function of the [AUTO] button.
AUTO TAKE
I
When the video of the A/PGM bus is selected, switches to the video of the B/PST bus. The
transition time is specified by the TRANSITION TIME menu item “WIPE/MIX TIME.”
H
AUTO TAKE
I
Switches the video between A/PGM bus and B/PST bus. The transition time is specified by the
TRANSITION TIME menu item “WIPE/MIX TIME.”
CUT
I
When the video of the A/PGM bus is selected, switches to the video of the B/PST bus as a cut.
H
CUT
I
Switches the video between A/PGM bus and B/PST bus as a cut.
TRANSFORM
I
When the video of the A/PGM bus is selected, switches to the video of the B/PST bus as a cut only
while you’re holding down the button.
PANEL OPERATION
Specifies the operation mode for video transitions.
A/B
The video of the bus toward which the video fader is slided becomes the final output.
PGM/PST
The video on the A/PGM bus is always the final output. Select the preview output video (the
video to be output next) for the B/PST bus side.
PANEL LOCK
ENTER Displays the PANEL LOCK menu.
Enable (ON) or disable (OFF) the panel lock.
Menu item Value
(bold text: default value)
Explanation
ALL SW & VOLUME
OFF
, ON The following settings are turned on/off together.
A/PGM 1–4 SW OFF , ON A/PGM cross-point [1]–[4] buttons
B/PST 1–4 SW OFF
, ON B/PST cross-point [1]–[4] buttons
CUT SW OFF , ON [CUT] button
AUTO SW OFF
, ON [AUTO] button
1/5–4/8 SW OFF , ON [1/5]–[4/8] buttons
MODE SW OFF , ON [MODE] button
TRANSITION SW
OFF
, ON [TRANSITION] button
VIDEO FADER OFF , ON Video fader
PinP SW OFF
, ON [PinP] button
SPLIT SW OFF , ON [SPLIT] knob
CONTROL KNOB OFF , ON [CONTROL 1] [CONTROL 2] knobs
DSK PVW SW
OFF
, ON [DSK PVW] button
DSK ON SW OFF , ON [DSK ON] button
OUTPUT FADE OFF
, ON [OUTPUT FADE] knob
AUDIO LEVEL OFF , ON [AUDIO IN 1] [AUDIO IN 2] [LINE IN] [MAIN] knobs
AUDIO GAIN OFF , ON [AUDIO GAIN 1] [AUDIO GAIN 2] knobs
SETUP (LINK) SW OFF , ON [SETUP] button
LIMITER SW OFF , ON [LIMITER] button
(*17) A change in the setting is not applied until you press the [VALUE] knob to confirm.
(*18) This can be set if “PANEL OPERATION” is “A/B.”