SX-UP2 Installation Guide
For Canada
CLASS B NOTICE
This Class B digital apparatus meets all requirements of the
Canadian Interference-Causing Equipment Regulations.
CLASSE B AVIS
Cet appareil numérique de la classe B respecte toutes les
exigences du Règlement sur le matériel brouilleur du
Canada.
ROLAND DG CORPORATION
1-6-4 Shinmiyakoda, Hamamatsu-shi, Shizuoka-ken, JAPAN 431-2103
MODEL NAME
: See the MODEL given on the rating plate.
RELEVANT DIRECTIVE : EC ELECTROMAGNETIC COMPATIBILITY DIRECTIVE (89/336/EEC)
For the USA
COMPLIANCE INFORMATION STATEMENT
Responsible Party
: Roland DGA Corporation
Address
: 15271 Barranca Parkway Irvine,
CA 92618 U.S.A.
Telephone
: 949-727-2100
Type of Equipment
: USB to PARALLEL Adapter
Model Name
: SX-UP2
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules.
These limits are designed to provide reasonable protection
against harmful interference in a residential installation.
This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio
communications.
However, there is no guarantee that interference will not
occur in a particular installation.
If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and
receiver.
- Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician
for help.
Unauthorized changes or modification to this system can void
the users authority to operate this equipment.
Thank you very much for purchasing the SX-UP2.
•To ensure correct and safe usage with a full understanding of this
product's performance, please be sure to read through this manual
completely and store it in a safe location.
•Unauthorized copying or transferral, in whole or in part, of this
manual is prohibited.
•The contents of this operation manual and the specifications of this
product are subject to change without notice.
•The operation manual and the product have been prepared and tested
as much as possible. If you find any misprint or error, please inform
us.
•Roland DG Corp. assumes no responsibility for any direct or indirect
loss or damage which may occur through use of this product,
regardless of any failure to perform on the part of this product.
•Roland DG Corp. assumes no responsibility for any direct or indirect
loss or damage which may occur with respect to any article made
using this product.
Windows
®
and
Windows NT
®
are registered trademarks or trademarks of Microsoft
®
Corporation in the United States and/or other countries.
Macintosh and Mac OS are registerd trademarks or trademarks of Apple Computer, Inc. in the USA and other countries.
Other company names and product names are trademarks or registered trademarks of their respective holders.
Copyright © 2001 Roland DG Corporation.
*In this manual, the term "product unit" refers to an output device from Roland DG Corp
.
Checking the Accessories
The following items are packed together with the unit.
USB/parallel conversion cable
*Floppy Disk
(USB driver for Windows 98/Me)
Roland License Agreement
Installation Guide (This manual)
*You can also download a USB driver for Windows 98/Me from the Roland DG Corp. website (http://www.rolanddg.com/download.html).
Setting Up the SX-UP2
< If Your’re Using Windows >
Operating System
Windows 98/Me or Windows 2000
(Windows 95 and Windows NT 4.0 are not supported.)
Computer Conditions
1) Computers preinstalled with Windows 98, Me, or 2000 at the time of purchase
(This includes such computers later upgraded to Windows Me or 2000.)
2) Computers on which USB operation is assured by the manufacturer of computers
• The ability to make a USB connection depends on the specifications of the computer. To determine whether the computer you're using
is capable of correct USB operation, check with the manufacturer of the computer.
• Do not use a USB hub or the like.
System Requirements
Installing the USB Driver
Windows 98
1.
Place the floppy disk (USB driver for Windows 98/Me) in the floppy disk drive.
2.
Switch on the product unit and connect the SX-UP2 cable. The [Add New Hardware Wizard] appears. Click [Next].
3.
Select [Search for the best driver for your device. (Recommended)], then click [Next].
4.
Select the [Floppy disk drives] check box, then click [Next].
5.
The confirmation screen for driver installation appears. Click [Next], then click [Finish] to finish installing.
6.
When the [Add New Hardware Wizard] appears, click [Cancel] to quit it. Install the included printer driver for the product unit sepa-
rately. If you already installed printer driver, the message for requiring printer driver appears. Click [Cancel], and cancel installation.
Windows Me
1.
Place the floppy disk (USB driver for Windows 98/Me) in the floppy disk drive.
2.
Switch on the product unit and connect the SX-UP2 cable. The [Add New Hardware Wizard] appears. Click [Next].
3.
Select [Automatic search for a better driver (Recommended)], then click [Next]. Installation of the USB driver starts.
If installation does not start, follow the procedure for Windows 98 to install.
4.
At the end, click [Finish].
5.
When the [Add New Hardware Wizard] appears, click [Cancel] to quit it. Install the included printer driver for the product unit sepa-
rately. If you already installed printer driver, the message for requiring printer driver appears. Click [Cancel], and cancel installation.
Windows 2000
1.
Log on to Windows 2000 as a member of "Administrators" or "Power Users" group.
2.
Switch on the product unit and connect the SX-UP2 cable. The USB driver is installed automatically.
3.
When the [Add New Hardware Wizard] appears, click [Cancel] to quit it. Install the included printer driver for the product unit sepa-
rately. If you already installed printer driver, the message for requiring printer driver appears. Click [Cancel], and cancel installation.
Setting Up the SX-UP2
< If Your’re Using Macintosh >
Specifying the Output Port
Make the setting for the output port used by the printer driver for the connected product unit, Roland CutChoice, or the like.
1.
Restart your computer.
2.
When printer driver or Roland CutChoice are not already installed, install them.
3.
Select [USB00*] for output port.
*For more information about how to install and make the setting for the output port, refer to the documentation for the product unit.
Operating System
Mac OS 8.6 to 9.X (except Mac OS 9.0.2 to 9.0.3)
Computer Conditions
Use Macintosh which USB operation is assured by the manufacturer of computers.
• The ability to make a USB connection depends on the specifications of the computer. To determine whether the computer you're using is
capable of correct USB operation, check with the manufacturer of the computer.
• Do not use a USB hub or the like.
Setup Procedure
*If you intend to use the SX-UP2 cable to connect the product unit with a Macintosh, first check to make sure the product unit is compat-
ible with the Macintosh.
1.
Turn on the product unit.
2.
Use the SX-UP2 cable to connect the product unit to the computer.
The SX-UP2 cable is a USB/parallel conversion cable for connecting a product unit from Roland DG Corp. to a USB port on your computer. You
can connect the product unit which is compatible with SX-UP2 cable.
System Requirements
