Roland SP-505, Service Notes

Page: 17 / 48

17
SP-505
1.
Save user area data on the SmartMedia by using [USERS DATA SAVE
AND LOAD] in this service note.
2.
Connect MIDI OUT if the MIDI sequencer can playback SMF data and
SP-505 MIDI IN by MIDI cable.
3.
Turn on the power while pressing the [F1], [F2] and [F3] buttons.
4.
After “MIDI UPDATER” is displayed, it enters the data receiving waiting
condition.
5.
Insert the delivered 3.5 inch disk (P/No. 17041086) for updating into the
MIDI sequencer.
Playback “_00001.MID” from the MIDI sequencer.
6.
When updating is completed, SSUM and the TSUM are displayed.
fig.up-midi1
7.
Turn off the power.
Turn on the power while pressing the [ENTER] and [EXIT] buttons.
8.
Checking the Checksum, and Turn off the power.
9.
After all procedures are completed, load user data by using [Loading
Momory card data in into internal Memory].
Updating by SmartMedia
Required Items
• Update & factory data card for Service (P/No. 17041085)
Perform the following procedure when updating with SmartMedia.
1.
Save user area data on the SmartMedia by using [USERS DATA SAVE
AND LOAD] in this service note.
2.
Insert the delivered SmartMedia (P/No. 17041085) for updating into the
SP-505.
3.
Turn on the power while pressing the [SONG], [PTN] and [BPM] buttons.
4.
It will be automatically updated when the SmartMedia is recognized.
5.
When updating is completed, “Complete!!” is displayed.
fig.up-midi2
6.
Turn off the power.
Turn on the power while pressing the [ENTER] and [EXIT] buttons.
7.
After checking the Checksum number, turn off the power and remove the
SmartMedia from the SP-505.
8.
After all procedures are completed, load user sample and pattern data by
using [Loading Memory Card Data Into Internal Memory].
TEST MODE
0. contents
1.Required Items
2.Test items list
3.Test mode types and how to enter each test mode
4.Switch operations during the test mode
5.Test contents
1.Required Items
1.
Foot Switch (FS-5U etc)
2.
MIDI Cable
3.
Oscillator
4.
Oscilloscope
5.
Noise Meter
6.
An Instrument with a DIGITAL OUT (OPTICAL/COAXIAL) such as a
CD player or BR-8, BR-532,VF-1,VS-840(EX/GX)
*The instrument must have a digital signal output for a sampling rate of
44.1kHz.
7.
SmartMedia 1 (Update & factory data card for Service (P/No.17041085)
supplied by the service center)
8.
SmartMedia 2 (3.3V product, initialized with more than 8MB available
space)
2. Test items list
[1] DEVICE CHECK
Displays the version and checks each device (CPU, DRAM, NAND FLASH,
FLASH ROM and Gate Array).
[2] PRESET LOAD
Loads the preset data (PRESET BANK 1-4 and USER BANK 1).
If user data exists in the USER BANK 1, follow the procedure in “Saving and
loading data”, and backup the data.
[3] SW & LED CHECK
Checks the switches (including the FOOTSW) and the LEDs.
[4] CONTROL KNOB CHECK
Checks the control knobs ([CTRL 1]-[CTRL 3]).
[5] ENCODER CHECK
Checks the encoder (the [VALUE] knob).
[6] LCD CHECK
Checks the LCD display.
[7] LINE IN CHECK
Checks the LINE IN jacks.
[8] PHONES CHECK
Checks the PHONES jack.
[9] MIC CHECK
Checks the MIC jack.
[10] DIGITAL IN CHECK
Checks the DIGITAL IN jacks (COAXIAL and OPTICAL).
MIDI UPDATER
ADRS SSUM TSUM
1EFE **** ****
CARD UPDATER
-- Complete!! --