Roland KIWI-3P Manual Download

Page: 46 / 60

Continuous Controllers

Second

Third

Notes

Start/Stop Arp

$67 (103)

$yy

$00-$3f (0-63)

Arp Stopped

$40-$7f (64-127)

Arp Playing

Start/Stop Seq

$68 (104)

$yy

$00-$3f (0-63)

Seq Stopped

$40-$7f (64-127)

Seq Playing

Mix ENV Source

$69 (105)

$yy

$00-$0f (0-15)

ENV 1 Normal

$10-$1f (16-31)

ENV 1 Inverted

$20-$2f (32-47)

ENV 2 Normal

$30-$3f (48-63)

ENV 2 Inverted

$40-$4f (64-79)

ENV 3 Normal

$50-$7f (80-127)

ENV 3 Inverted

Chorus Off/Auto/Manual

$6a (106)

$yy

$00-$3f (0-31)

Chorus Off

$20-$5f (32-63)

Chorus On Auto

$40-$7f (64-127)

Chorus On Manual

Matrix 0 Level

$6c (108)

$00-$7f (0-127)

Matrix 1 Level

$6d (109)

$00-$7f (0-127)

Matrix 2 Level

$6e (110)

$00-$7f (0-127)

Matrix 3 Level

$6f (111)

$00-$7f (0-127)

Matrix 4 Level

$70 (112)

$00-$7f (0-127)

Matrix 5 Level

$71 (113)

$00-$7f (0-127)

Matrix 6 Level

$72 (114)

$00-$7f (0-127)

Matrix 7 Level

$73 (115)

$00-$7f (0-127)

Matrix 8 Level

$74 (116)

$00-$7f (0-127)

Matrix 9 Level

$75 (117)

$00-$7f (0-127)

Master Tune

$76 (118)

$00-$7f (0-127)

Program Change

$77 (119)

$yy

$00-$7f (0-127)

Program Number

Note – this is only here because the BCR2000 is not able

to step programs using two buttons

All Sound off

$78 (120)

Stops all output immediately

All Notes off

$7b (123)

Stops all output immediately

Real Time Commands

Midi Clock

$f8 (248)

Midi Timing Clock

Start

$fa (250)

Start Sequence Play

Stop

$fc (252)

Stop Sequence Play

Midi Sysex Support

Function

Transmitted

Recognized

Notes

Basic ID

1-16

1-16, Omni

Set using Device ID in Global Variable S:B:4

Load

Dump

www.kiwitechnics.com

Kiwi-3P Matrix Upgrade User Manual v1.2

Summary of Contents for KIWI-3P





























































Search results

Summary of Contents for KIWI-3P

Reviews:

Related manuals for KIWI-3P

Brands by name

Popular brands

Roland KIWI-3P, Manual

Search results

Summary of Contents for KIWI-3P

Reviews:

Related manuals for KIWI-3P

Brands by name

Popular brands