background image

 

9

 

Making the Connections

 

Switching the Power On and 

 

Off

 

Once the connections have been completed, turn on power to 

your various devices in the order specified. By turning on 

devices in the wrong order, you risk causing malfunction 

and/or damage to speakers and other devices.

 

1.

 

Make sure that all volume controls on the KC-150 and 

connected devices are set to 0.

 

2.

 

Turn on all the devices connected to the KC-150’s input 

jacks (CH 1 through CH 4 and AUX IN).

 

3.

 

Turn on the KC-150.

 

4.

 

Switch on any equipment connected to the KC-150’s 

LINE OUT or SUBWOOFER OUT jacks.

 

5.

 

Adjust the volume levels for the devices.

 

6.

 

Before switching off the power, lower the volume on 

each of the devices in your system and then TURN OFF 

the devices in the reverse order to which they were 

switched on.

 

* This unit is equipped with a protection circuit. A brief interval 

(a few seconds) after power up is required before the unit will 

operate normally. For protection from sudden big sound, always 

make sure to have the volume level turned down before 

switching on power. Even with the volume all the way down, 

you may still hear some sound when the power is switched on, 

but this is normal, and does not indicate a malfunction.

* If you need to turn off the power completely, first turn off the 

POWER switch, then unplug the power cord from the power 

outlet. Refer to “Power Supply” (p. 5).

 

About the Volume-level 

 

Settings

 

In order to get optimum sound from the KC-150 when 

performing, set the volume as described below.

 

1.

 

Operate the CH 1 through CH 4 volume knobs to adjust 

the volume level for channels 1 through 4.

 

fig.11

 

Adjust the volume balance for channels 1 through 4 at this 

time.

 

* To adjust the volume level of equipment connected to the AUX 

IN jacks, use the controls on such equipment. 

 

2.

 

Adjust the LOW and HIGH knobs to obtain the tone you 

want.

 

3.

 

Use the VOLUME knob to adjust the overall volume 

level.

 

fig.12

 

* If the sound is distorted, lower the CH 1 through CH 4 volume 

knobs, VOLUME knob and/or the volume knobs for devices 

connected to the input jacks (CH 1 through CH 4 and AUX 

IN).

KC-150_e_A4.book 9 ページ 2005年4月28日 木曜日 午前9時0分

Summary of Contents for KC-150













Reviews: