44
MFX/Chorus/Reverb Parameters
13: MLT STAGE PHASER
Extremely high settings of the phase difference produce a deep phaser effect.
Resonance
Mix
L in
R in
L out
R out
Pan R
Pan L
2-Band
EQ
Multi Stage
Phaser
Parameter
Value
Explanation
Mode
4-STAGE, 8-STAGE,
12-STAGE, 16-STAGE,
20-STAGE, 24-STAGE
Number of phaser stages
Manual #
0–127
Adjusts the basic frequency from which the
sound will be modulated.
Rate #
0.05–10.00[Hz], note
Frequency of modulation
Depth
0–127
Depth of modulation
Resonance #
0–127
Amount of feedback
Mix #
0–127
Level of the phase-shifted sound
Pan #
L64–63R
Stereo location of the output sound
Low Gain
-15–+15[dB]
Gain of the low range
High Gain
-15–+15[dB]
Gain of the high range
Level
0–127
Output level
14: INFINITE PHASER
A phaser that continues raising/lowering the frequency at which the sound is
modulated.
Infinite Phaser
2-Band EQ
L in
R in
L out
R out
Pan R
Pan L
Parameter
Value
Explanation
Mode
1–4
Higher values will produce a deeper phaser effect.
Speed #
-100–+100
Speed at which to raise or lower the frequency at which
the sound is modulated (+: upward / -: downward)
Resonance #
0–127
Amount of feedback
Mix #
0–127
Volume of the phase-shifted sound
Pan #
L64–63R
Panning of the output sound
Low Gain
-15–+15[dB]
Amount of boost/cut for the low-frequency range
High Gain
-15–+15[dB]
Amount of boost/cut for the high-frequency range
Level
0–127
Output level
15: RING MODULATOR
This is an effect that applies amplitude modulation (AM) to the input signal,
producing bell-like sounds. You can also change the modulation frequency in
response to changes in the volume of the sound sent into the effect.
L in
R in
L out
R out
Ring Mod
2-Band EQ
2-Band EQ
Ring Mod
Parameter
Value
Explanation
Frequency #
0–127
Adjusts the frequency at which modulation is
applied.
Sens #
0–127
Adjusts the amount of frequency modulation
applied.
Polarity
Determines whether the frequency modulation moves towards higher
frequencies or lower frequencies.
UP
Higher frequencies
DOWN
Lower frequencies
Low Gain
-15–+15[dB]
Gain of the low frequency range
High Gain
-15–+15[dB]
Gain of the high frequency range
Balance #
D100:0W–D0:100W
Volume balance between the direct sound (D)
and the effect sound (W)
Level
0–127
Output level
16: STEP RING MOD
This is a ring modulator that uses a 16-step sequence to vary the frequency at which
modulation is applied.
L in
R in
L out
R out
Step Ring Mod
2-Band EQ
2-Band EQ
Step Ring Mod
Parameter
Value
Explanation
Step 01–16
0–127
Frequency of ring modulation at each step
Rate #
0.05–10.00[Hz], note Rate at which the 16-step sequence will cycle
Attack #
0–127
Speed at which the modulation frequency
changes between steps
Low Gain
-15–+15[dB]
Amount of boost/cut for the low-frequency range
High Gain
-15–+15[dB]
Amount of boost/cut for the high-frequency
range
Balance #
D100:0W–D0:100W
Volume balance of the original sound (D) and
effect sound (W)
Level
0–127
Output level
MEMO
You can use MFX control to restart the step sequence from the beginning (p. 18,
17: TREMOLO
Cyclically modulates the volume to add tremolo effect to the sound.
L in
R in
L out
R out
Tremolo
2-Band EQ
2-Band EQ
Tremolo
Parameter
Value
Explanation
Mod Wave
Modulation Wave
TRI
Triangle wave
SQR
Square wave
SIN
Sine wave
SAW1, 2
Sawtooth wave
SAW1
SAW2
Rate #
0.05–10.00[Hz], note
Frequency of the change
Depth #
0–127
Depth to which the effect is applied
Low Gain
-15–+15[dB]
Gain of the low range
High Gain
-15–+15[dB]
Gain of the high range
Level
0–127
Output level
18: AUTO PAN
Cyclically modulates the stereo location of the sound.
L in
R in
L out
R out
Auto Pan
2-Band EQ
2-Band EQ
Auto Pan
Parameter
Value
Explanation
Mod Wave
Modulation Wave
TRI
Triangle wave
SQR
Square wave
SIN
Sine wave
SAW1, 2
Sawtooth wave
SAW1
SAW2
L
R
L
R
Rate #
0.05–10.00[Hz], note
Frequency of the change
Depth #
0–127
Depth to which the effect is applied
Low Gain
-15–+15[dB]
Gain of the low range
High Gain
-15–+15[dB]
Gain of the high range
Level
0–127
Output level
3
3
3
3
3
3